YWEE745H0FH0 Whirlpool Range - Instructions

I've replaced oven heating elements before, but never in a 3 year old electric range oven. I watched the video again after the element arrived, and installation was easy with only 2 screw drivers. I was concerned about the repair when I saw the severity of damage to the old heating element and the underside of the bottom oven metal/ceramic plate, which was almost burned (a hole) through. After finishing the installation the oven showed it was preheating but no heat was being generated. A couple of phone calls later, a Whirlpool repair technician told me the main control panel needed replaced- $385 much higher cost due to chip shortage, inflation, and would take 2 months to arrive due to supply chain issues. So I don't know yet if the element is good or not. I am disappointed that the element blew in a relatively new appliance, but a total cost of $600 in a 3 year old oven is still probably better than $1200 for a new oven which is double the price I paid in 2018. Part failures never come at a good time but 2 months without an oven at Christmas & New Years is added frustration. When the heating element burned out there was a loud buzzing sound associated with the failure, which I've never experienced before and there were flames coming from underneath the bottom plate in the oven for an extended period of time. The repair for the heating element itself went smooth, but be advised you may get into more than just the element.

It was easy to remove the old oven door gasket. Just a little tug was all that was needed. Installing new gasket was just as simple as tucking in the gasket end into the hole at the bottom and pushing the clip in the corresponding hole.
TIP: roll the end of the gasket and feed into the hole then use a small tipped screw driver or the point of a needle nose plier to finish installing the ends into the hole at the bottom of the door opening.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I shut off the breaker to the stove. I removed 2 screws from the underside of the cooktop at the front of the unit. I raised the cooktop and had my helper hold the top at an angle to access the burner. I removed 2 screws attached to the burner and then loosened the 2 clips and moved them to release the burner. I transferred the electrical connections from the old to the new. Reinstalled the burner and cooktop. Turned the breaker on, tested the new burner and I was fone

I first shut off the breaker, then, after pulling the stove away from the wall, I unplugged it. I removed the two screws in the back of the stove which came off easily. I removed the two screws inside the oven and removed the bottom plate. I noticed the heating element I was changing had braces along the bottom. I had to remove the two screws and removed the burnt out element. The new element did not have the braces the original element had, but it fit in perfectly. Then I replaced all the screws, plugged it in and turned on the breaker and it worked. The only thing that we noticed is there’s a clicking sound every time the temperature increases. Not sure what that is.

Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair

Your technician suggested that the control knob unit was defective. I ordered the part and after watching your video, I was able to make the repair

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

Wanted third oven rack. No problem.

Took 2 screws holding vent trim to door removed 2 screws holding handle to vent trim, put handle on new vent trim put vent trim back on door

Purchased new switch shut off breaker unscrew the back plate remove front knob and two screws that hold it on remove the two electrical clips from old switch then reinstall in reverse order. Also watched the youtube video before hand, great help!

There is a good video on YouTube that shows exactly how to replace the bake element. Had mine fixed in 15 to 20 minutes. Saved me about $150 by not having to call repairman.

very expensive to buy the part but just tighten the screw intot eh predefined place.

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy