YWEE730H0DS1 Whirlpool Range - Instructions

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

I watched then followed the video. I could not remove the top, so I used a can from the cabinet to support and hold the top. That gave me enough room to get the old fan out and the new fan in. Thank you PartsSelect.

Ordered new element from PartSelect. It arrived shortly. It did not match the original. Guy at appliance store explained how I could connect the wires on the new one. It still did not fix the problem. A repair man tried for 2.5 hours to fix it with no success. Now I will return the replacement element in the return envelope provided.

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

Took 2 screws holding vent trim to door removed 2 screws holding handle to vent trim, put handle on new vent trim put vent trim back on door

Wanted third oven rack. No problem.

There is a good video on YouTube that shows exactly how to replace the bake element. Had mine fixed in 15 to 20 minutes. Saved me about $150 by not having to call repairman.

very expensive to buy the part but just tighten the screw intot eh predefined place.

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair

the part conections were different from the original.so the first i did was to call parts direct to see if someone will help.NOBODY WAS ABLE TO HELP. so i had to use a lot of common sense to install this my self.

Pop old one out and new one in

The instructions given on this website were more than adequate, even though the element had been updated and now has only 1 point to screw down

put back together with parts ordered. Parts arrived in 2 days!!!! and saved my large dinner party the following day from being ruined. Thank you so much for your parts inventory and for Jenn Air supplying only the part needed and not the entire door. It was a life saver!

Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white too.

Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.