YMER8875WB0 Whirlpool Range - Instructions

I watched a couple of online videos to determine what could be wrong with my oven and how to fix it. I ordered the part and it only took a half day to arrive at my door. After removing 3 screws in the panel on the bottom of the oven to expose the bake element, I pulled the element from the wiring. Even though I was careful, one of the wires slipped away and could not be fished back out. So I removed a few screws from the back of the oven, easily found the wire and connected it to the new element. It was a pretty easy fix that would have been even easier if the wire had not slipped into the back of the oven. I am a retired female, and I strongly recommend saving a chunk of money by doing this job yourself.

Turn off power--Remove bottom cover inside the oven---Undo three screws holding broken element in place--Remove element by pulling out ,and carefully detach from power connection.Reverse the procedure with the new element.In doing this myself I saved $90 for a repairman to come and diagnose the problem, and another $90 to bring back and install the element which cost $62

Easy just loosened screws took apart door, removed broken glass and installed new glass.It took longer to clean the stove! Lol!

Exactly how the video provided showed. It was pretty simple.I feel pretty cheesy about doing this myself. Thank You!

First removed 3 screws from top of door and the 3 bottom screws. To remove hinges there are 2 screws on the bottom ends remove those and then there is 1 in the center of hinge remove slide out old hinges and install new ones.The hinges have to be in the extended position I then put the needle nose pliers on the top end of hinge because they kept snapping shut before it engaged with the receptacle I put on one side when it was in I released the plier and it hooked I then proceeded to the opposite side it shouldn't have taken so long once I used the locking plier I was done in 10 minutes.

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.

Very easy repair watched video from parts plus.Made repair

unplugged the range, removed the cooktop left & right front screws, unplugged left & right plug & unscrewed ground wire. Parts arrived fast & reassembled. . Happy, Happy, Happy! Happy Wife...Happy Life!

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.

My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.

Easy change! Two screws in front and grounding strap screw-lifted out and turned stove top upside down on table. three more screws for burner element and then reinstall with first two screws and grounding strap screw.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.