YMER8670AB0 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosalind from APOLLO, PA
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the oven temperature was not working right. I installed a new oven sensor. Works get now
Watch the video...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from HARMONY, MN
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
temp level uneven
after watching the video, installed the temp sensor. Super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from THE VILLAGES, FL
- Parts Used:
- W10779716
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
After watching the video, I said to my wife that this is a simple installation. However, I’m looking at the screws, I did not have the correct screwdriver to remove the screws. I had to go out and buy that. After that, it was not a problem.
I first shut off the breaker, then, after pulling the stove away from the wall, I unplugged it. I removed the two screws in the back of the stove which came off easily. I removed the two screws inside the oven and removed the bottom plate. I noticed the heating element I was changing had braces along the bottom. I had to remove the two screws and removed the burnt out element. The new element did not have the braces the original element had, but it fit in perfectly. Then I replaced all the screws, plugged it in and turned on the breaker and it worked. The only thing that we noticed is there’s a clicking sound every time the temperature increases. Not sure what that is.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from HUMBOLDT, SD
- Parts Used:
- W11047668
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dual burner right front not heating properly
Purchased new switch shut off breaker unscrew the back plate remove front knob and two screws that hold it on remove the two electrical clips from old switch then reinstall in reverse order. Also watched the youtube video before hand, great help!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lou ann from MARTINSBURG, WV
- Parts Used:
- W10779716
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake element burned out
There is a good video on YouTube that shows exactly how to replace the bake element. Had mine fixed in 15 to 20 minutes. Saved me about $150 by not having to call repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ENID, OK
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven light kept burning out instantly
Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from COON RAPIDS, MN
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Worn/Bulb Socket
It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandeep from EDINA, MN
- Parts Used:
- W10777162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
screw came off
very expensive to buy the part but just tighten the screw intot eh predefined place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Assad from PARKER, CO
- Parts Used:
- W10779716
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The oven's lower heating element needed replacement
Watched the video and realized this was something I could do myself...bear in mind I'm not exactly a handyman! Took me about 30min as the oven also needed some cleaning...my tenant definitely needs to use the self-cleaning!
I have to note, although the heating element was covered by Maytag's 10yr limited parts warranty, I decided to purchase from PartSelect since Maytag could not provide a ship date and I couldn't keep my tenant waiting! Supposedly Maytag had the part in stock but their warehouse was behind because of the pandemic...what a lame excuse! Almost a month later, Maytag has yet to ship the part! Needless to say, am very disappointed in Maytag's after sales and warranty program! I get the impression, they just wanted to pressure me to buy the new part!
Lastly, was very pleased and impressed by PartSelect's customer service! Their website was very easy to use, less expensive than buying direct from Maytag and the part was shipped same day! Thank you PartSelect!
I have to note, although the heating element was covered by Maytag's 10yr limited parts warranty, I decided to purchase from PartSelect since Maytag could not provide a ship date and I couldn't keep my tenant waiting! Supposedly Maytag had the part in stock but their warehouse was behind because of the pandemic...what a lame excuse! Almost a month later, Maytag has yet to ship the part! Needless to say, am very disappointed in Maytag's after sales and warranty program! I get the impression, they just wanted to pressure me to buy the new part!
Lastly, was very pleased and impressed by PartSelect's customer service! Their website was very easy to use, less expensive than buying direct from Maytag and the part was shipped same day! Thank you PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from DEFIANCE, OH
- Parts Used:
- W11171119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Burner went out
Two screws to remove glass top. 2 connectors to remove. Removed glass top and put it upside down. Remove 4 wires and 2 Phillips screws. Reverse steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from WAXAHACHIE, TX
- Parts Used:
- W11047722
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
old coils burned in two pieces.
Had an electrician to do the job for me.
Turn off 220 voltage, unplug and remove clips. replace it with new part. Check part before replacing the top of range, if it works, the electricity can be turned back on. Repair done.
Turn off 220 voltage, unplug and remove clips. replace it with new part. Check part before replacing the top of range, if it works, the electricity can be turned back on. Repair done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from CHARLES TOWN, WV
- Parts Used:
- W10779716
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Lower element shorted out
Followed the video on this site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bobby from HERSCHER, IL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
range would not heat right
very easy watched the howto you gave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from SAN ANGELO, TX
- Parts Used:
- WPW10434452
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Front dual burner would stay on.
First I threw the breaker for the stove to off. I pulled the whole stove out, removed the back cover, removed the knob from the faulty control switch and then unscrewed the two screws holding in the switch. I then pulled the wires from the back of the faulty switch, inserted the wires into the new switch, reattached the two screws that hold the switch in. I threw the breaker back on and turned the burner on long enough to make sure that both dual elements came on and went off like they should. At that point I reattached the back cover and shoved the stove back onto its' slot. All is well and all went well.
Was this instruction helpful to you?
Thank you for voting!