YMER5605YW1 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joanne from Negaunee, MI
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.
Took off the screws on the back of the stove and took out the sensor, and put in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Oceanside, CA
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Damaged Socket When Removing Bulb Base
This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Titusville, FL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.
Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoAnne from Harrison, AR
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven element burnt out
unscrew two screws..took old element out, put perfect fit new element in,screw two screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Weston, WI
- Parts Used:
- WPW10308477
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
lower element burned out
So easy. Unplug the range. (really important. You're working with wiring after all) Unscrew the metal plate holding the bake element in place, gently pull out the wires and detach the element from them. (the element just pulls off, but it was attached pretty tightly so I did have to use needlenose pliers to get a better grip on it.) Then simply plug in the new bake element, push the wires back in, reattach the metal plate and bake a cake! Don't even think about calling a repairman for this one! It took under 10 minutes once I got around to ordering the element. (none of the local stores carried them)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Ft Myers, FL
- Parts Used:
- WPW10118454, WP8523175
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Glass door front fell out during cleaning and shattered
Install bottom door trim first...Remove upper door handle and set new glass door front piece in place and re install upper door handle and tighten all screws...Looks great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thaddeus from Washington, DC
- Parts Used:
- WPW10118454
- Difficulty Level:
- Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken outer range door glass
Using 4 strips of duct tape was useful,in holding the glass to the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Elk River, MN
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element burned out
I found a video on YouTube and watched it showing how to change the element - then I performed the repair based on the instructions and recommendations in the video. The video had some good recommendations and cautions that helped ensure a successful repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jon from lexington, GA
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Chared Bake element
Unplug oven, open oven door wide,pull out racks, clean reside that old element left. I used power drill with phillips head bit,pulled out old element, and disconnected wires from clips. Connected new element to wires, and Presto.Turned bake element to 300 deg.and waited only to see it red and ready to cook.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobbye from Ethelsviolle, AL
- Parts Used:
- WPW10308477
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom element was burned out
I was 100% happy with the whole process! The part arrived on schedule, it was exactly what I wanted! The best part of the story is I am a 77 year old lady whose husband was out of town and had never done this before. I could not have been happier with the process! Thanks again and I will use PartSelect again!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- larry from springville, AL
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Was Not Heating As It Should
Removed lower oven rack. Unplugged stove,removed 2 screws holding element in place,pulled element forward unplugged 2 wires. Reversed proc. To reinstall . Very simple. Parts were here in less than 24 hrs using standard shipping. Very good service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PATRICIA from GEORGETOWN, MA
- Parts Used:
- W10763667
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drawer Glide Snapped Off And Broke
Snapped in the new drawer glide. Took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lewisville, NC
- Parts Used:
- WP3149404
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element would not get red hot
Replaced Infinite control switch in just a few minutes. Unfortunately the new switch had a lose terminal that was not supposed to be in the switch that came from the factory that way. I connected the switch, turned it on, and it instantly shorted the switch out. At that point the lose terminal was real easy to see.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maxwell from Springdale, AR
- Parts Used:
- WPW10308477
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom element burnt into two pieces
Unplugged stove, opened door and removed two bolts with a phillips screwdriver. Pulled out old element and pulled off the two wire leads. Replaced with new element and reversed all steps...wallaaaaa.
Was this instruction helpful to you?
Thank you for voting!