YKFEG500EBL2 Whirlpool Range - Instructions

Removed back cover on range, removed two wires attached to element, then removed element by taking three screws out holding it in place. Installed new element in reverse order of removal. Only problem was relay on control panel board was sticking, and had to tap on it with screwdriver to finally get the oven to preheat.

Turned the breaker off. Removed the racks, pulled the oven out and removed the back. Disconnected and unscrewed the old sensor from the back, connected and screwed in the new one. Returned the racks and slid the oven back in.

The only remotely challenging part was disconnecting the old sensor. I had to figure out where to press with the flat screwdriver to get it to release.

I had found a good YouTube video and didn't use the app.

I watched a video on google on how to replace the element and then looked on the internet to order the element. When the part arrived, I pulled the range out and unplugged it. Then I watched the video again and followed the techs instructions to remove the element and replaced it with the new one. It’s a very simple process that I think almost anyone can do . The online videos make the job easier because they show exactly the order of disassembly and assembly, and Part Select helped with finding the right part and shipping it in a timely manner. Thank you!

An easy repair. I just needed a screwdriver.
I watched the video that you sent me with the part. I followed the directions in the video and the job was completed in 30 minutes!
Easy Peazy!! I’m back to cooking!

Removed 2 screws on inside of oven door being careful not to let front oven door glass to fall off of door. It would probably be a good idea to use tape to hold glass on door before removing screws. Lifted out trim piece with handle and then removed handle and attached to new trim piece and screwed it back onto oven door.

Opened the breaker for the oven. Verified the power was off. Removed the racks from the oven. Using a screw driver removed two screws in the back of the oven holding down the steam bake bottom of the oven, pulled up from the back to get the pan out. Removed the screw holding the front of the element in place. Removed the screw in the shiny metal of the element at the back. Gingerly pulled the element to the front and as the element stopped slightly turned the element to let the prints come out. That part was challenging to get the angle right so not to damage the wires. Using a small Phillips screw driver I pushed in on the connector latch on the terminal and then pulled the terminals off the element one at a time. Follow all the steps in reverse to install the new one.

Shut beaker off
Unhooked wires on element back of stove
Removed all racks
Unscrewed lower plate cover
Removed element
Inserted new element
Rebooked wires to element
Reinstalled cover plate
Turned breaker back on
Turned range on and let heat up
Turned it off
Reinstalled racks

Unplug the appliance, remove the bottom cover inside the range and the cover in the rear to unplug the heating element. R&r the element, reinstall the covers and test for proper operation.

Took off top and pulled out old element and plugged in the new one

1) unplugged rnage from wall
2) took off back plate to unhook electrical from element
3)took door off of range for ease of access
4) removed the 2 screws i the back of tha bottom panel
5) removed 1 screw in front and 1 screw in back to be able to remove old element.
6)remove element and replace with new one.
7) reinstalled both screws and the bottom panle.
8) connected electrical to new element
9) replaced back cover and plugged in unit to wall
10) put range back in place.

Took out the bottom tray and the back cover panel, unplugged the old element and plugged the new one in and reassembled

I read the help section and it said that the element was likely to be the problem (84%) and the fuse had a 14% chance to be the problem so I purchased both. After watching the video I tried the element first and that's what it was so I returned the fuse, Thanks for the help and video.

The company said it would cost me $698 to repair. I had a 2 year warranty and that was 2 months out of date.

Again thanks for the help.

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Repair has not been made yet still waiting for the part. The part is on order and was told it would be shipped in 1/3 business days. Still waiting for the part to come from China. This is the problem with parts being made out side the U. S. A.