SF325PEGW0 Whirlpool Range - Instructions

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Unplug the stove. Remove the burners. Release the top of the stove by using a screwdriver to push in the spring clips on each side of the stove top. Pull out stove to access the back of the stove. Remove the back plates. Identify the defective igniter wire and remove. Install the new igniter wire. Screw the back panels back on. Snap the stove top back in place. Reinstall the burners. Push the stove back into place and plug in the stove. Test the burners.
One precaution - make sure you do not move the gas tubing under the stove top out of position. If you do, make sure you put it back in line with the gas valves.

new handle arrived black for white oven - screws did NOT fit new handle- glass came off the door when removing old handle

Turn gas off at tank. Oven rack out. 2 screws out of flame spreader and remove. 2screws from ignitor. Pull oven out from location to access rear bottom cover. 2 screws out and unplug ignitor. Guess what ? Reverse order. Not worth paying gas company over 250 dollars.

I just removed the bottom panel in oven and the igniter was right where the flames should be and I removed the two screws and replaced with new part. I replaced bottom oven panel. You need to remove rear panel and plug wire and replace rear panel. My problem was solve. It took 20-30 minutes tops.

The brief comments on how to with the order was most helpful, no problems replacing frame. Quality is good I thought the price was very high for the parts, considering plastic and metal pieces, but then again compared to new stove reasonable. Remove pieces replace back in order removed.

I use the table knife to slide the side of the stove to open the top. then I traced one of the wire to where it was hooked up and remove it and replaced it. I did them one by one.

Unscrewed the feet from the floor. Pried up the range top, removed burners. Unscrewed sides of the range from wooden cabinet it was recessed into. Unplugged range from outlet. Pulled range out into the open. Removed back cover. Discovered that I have the wrong replacement part.

I still don't have it back together! The first time we ordered the part the gentleman sent me the trim for the left side which seemed to be fine but while replacing it the old part (right side) broke. Ok. so I called to order same part but for the right side. Well, the lady told me I could only order the oven door trim kit, which seems to be too large. I don't think she understood me. Why the 1st time ordering I could get the left side only now when ordering the right side she says we don't sell it that way. Very confused and still can't use my oven since Dec,19th!!

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.

used a screwdriver. took very little time and effort

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy

Loosen 2 screws and put new part in and tighten 2 screws. After putting in new sensor stove gave me another code had new part in 5 min and part select would not take my part back.