1765^0A Whirlpool Range - Instructions

I unplugged the stove from the outlet, then removed the two burners I was going to be working on and the drip pans. Then I raised the top part of the stove and removed the screws holding the plug-in blocks to the stove. Then I cut the two wires going to the old plug-in block and stripped the wires back to match the new wire parts. Then I placed the sleeves over the new wires, then I placed the new wire beside the wire I stripped on the stove and screw on the wire cap making sure it was tight. I repeated this three more times, once I had all four wires connected I then placed the sleeves over the connections and heated them up until they were formed around the connection. Once I had all the connections done I placed one wire at a time into the plug-in block until it locked into place ( I looked at my old plug-in blocks first to make sure I placed the new wires in the correct way ).I then used the metal mounting bracket that matched my old ones and snapped the correct one onto each plug-in block. Before mounting them onto the stove I compared them to my old ones to make sure they were correct. Then I used the new screws to mount them to the stove. I took a second look at everything I had done before closing the top cover of my stove. After lowering the cover back into place I put both the drip covers in place and then installed the burners.I then plugged the stove back into the outlet and tried the burners. This was very simple and the video on the web site shows this very well which made my job very simple.

Pulled off the one remaining knob, installed the new ones. One minute and the stove works perfectly.

In my perpetual state of optimism, I hoped that the part description was incorrect and that the cost for the knob was actually a cost for a set of knobs. Woe to the consumer who doubts his own eyes! Yes, you will be paying about $25 after s/h for a single knob- but it matches, it works, it fits, and it takes less than 2 seconds to install, so kudos to the manufacturer who knew this would be a good form of supplemental income from their product... I still adore Whirlpool despite their exorbitant pricing on plastic knobs... :)

The first thing I did was to turn the power off to the stove by turning the Stove circuit breaker off at the Main breaker panel. I next removed the 4 burners by pulling them out of their plug-in blocks. I then removed the four screws that held the top of the stove to the body so I could access the bad plug-in block, the screws were located under each of the burners drip pans. I next removed the screw holding the bad block. I lifted up the top of the stove so as to relocate the bad block, with wires connected, through the opening of the back burner. The bad block was located in the front rt part of the stove and by rerouting this to the back I could lay the top down and have easy access to what I needed to replace. I next used the knife to make a cut down the length of the old shrink tubing so as to gain access to the old splice. I next removed the old wire nuts which allowed the removal of the bad block. I then install the new clips into the new block. I installed one each shrink tubing onto each of the pigtails from the new clips and twisted the one new wire to the stove wiring harnes were the old wire was connected . I connected the seconded wire in the same manner. I pulled on each wire to verify that they were tightly secured together. I then positioned each shrink tubing over each wire nut (you have to fold the wire nut and wires down against the wire so as the shrink tubing will slip over the wire nut) and used a heating tool (hair dryer on high) to shrink the tubing around the wire nutted connection. I next installed the metal clip that would hold the block to the stove top. I placed the new block back to the location where the old block came from and secured it with the new screw provided by the kit. I re-installed the four screws to hold the top down, plugged in the four burners, turned the power on at the breaker box and turned the burner on to test that it work.

Thought we was going to have to replace the range all together, due to most parts not being available for this model anymore. Since this is an expensive model, we did not look forward to having to replace it. So I thought just by chance I would check to see if anyone had parts to help in repairing it. Part Select did happen to have the Surface Plug-in block kit that was needed. After going at least a year with this problem, I am sooooo happy to say it is finally fixed and working great! Thanks much Parts Select.

replaced old, worn blocks with new style surface plug in block kits - all 4 burners. Completely resolved the problem at very low cost (less than $50.00).

1. Turn off circuit breaker, pull out element and remove reflector pan.
2. Unfasten terminal block mounting screw and remove terminal block from casing.
3. Cut wires as close to defective terminal block as possible (not as per instructions) since you will need the maximum possible length of wire.
4. Slip on heat shrink sleeves, strip stove wires and connect to new terminal block per instructions.
5. Heat shrink sleeves per instructions.

removed old Plug-in block by removing 1 screw and cutting 2 wires. (Screw was so tight and rusty that I had to use vise grips to remove it). Installed new Plug-in block with wire nuts and heat shrink wraps. YOU just have to make sure the wires are seated in the block properly. This job was much easier than I anticipated. The burner works great now!

Removed 2 screws, cut the wires, pulled the part out that the element plugs into. Replaced the old part with the new one and put the screws back in to hold it, reconnected the wires and plugged in the element. Turned stove on and Valaaaa! It was fixed in 10 minutes! Thanks for the great repair parts!

Replaced the knob by sliding it on.

I cut the power to the circuit. Removed the burner and then unscrewed the old aluminum plate attached to the range top cover. Opened the topcover to access the wires. I cut the two wires being sure that I left enough length. I then slipped the two new wires with the brass contacts into the new black plastic holder until it locked. Reattached the new metal plate to the range cover, fed the wires through and snapped the new plastic holder into the aluminum plate. Secured wire ends with the ceramic wire nuts. Total time about 30 minutes.

Drilled a pilot hole with a 1/16 th drill bit and tapped off screw head.

I opened the door to recieve the parcel from the courier. I opened the envelope containing the knobs. I took the knobs out of their plastic bags. I then place the knobs on the control stubs. The whole project took less than a minute and would not have been possible without PartSelect.com.

Thanks for everything!

Sincerely,

Dean Harley

removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy and quick repair

I followed the instructions provided.