WFG510S0AD2 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Raymond from BLOOMINGTON, MN
- Parts Used:
- 4396923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased home but stove had no broiler pan.
Purchased 2 piece broiler pan from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from LONGVIEW, TX
- Parts Used:
- WPW10110491
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gas burners would not automatically light when gas turned on
I went online and discovered the repair method and schematic of the range. I removed the spark module after first removing the upper rear panel cover and replaced with the new part module ordered from your company and now the spark module operates all the gas elements when they are turned on thus lighting the gas burners. My mother in law was thrilled, as she had been using matches and burning her finger tips,since the original range part malfunctioned. The only problem was the small screw from the original installation was not long enough , so it required some changes to get it affixed to the cabinet side.Thanks for the reasonable price and the right part for the job!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Terre Haute, IN
- Parts Used:
- WP8523175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom door trim was rusted
Removed oven door and the 3 screws holding the bottom door trim. Attached new trim piece and reinstalled oven door. Entire job took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from McDonough, GA
- Parts Used:
- WPW10330077
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
front safety glass broken
ordered new front and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delores from Warren, MN
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven light would not work--faulty socket
After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Pine Plains, NY
- Parts Used:
- WP3195097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven bottom had rusted out
Found that the two screws securing the bottom had rusted away allowing me to just lift the old bottom out. The new one fit in place exactly and really did not need the screws. Done in 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from OSWEGO, IL
- Parts Used:
- WP9758079
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not heat
Removed bottom panel. Unscrewed igniter. Replaced igniter. Reinstalled panel. Started oven before replacing panel. Easy install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from PAYETTE, ID
- Parts Used:
- WPW10299224
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
DOOR HINGE BROKEN, NOT SUPPORTING DOOR
Followed youtube instructions: lifted clips on door hinges, removed door. removed screws, removed rear cover, replaced right hinge. reassembled door. caution: door handle will fall off when top two screws are removed. Alignment of screws is some what difficult, requires awl.
Replace door, return locking clips to forward position, check door for operation.
Replace door, return locking clips to forward position, check door for operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from West Monroe, LA
- Parts Used:
- WP8523178
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bottom door trim was rusting
Simply removed three screws that held the door trim in place. Once the screws are removed be carefull because the front door glass is held in place by the bottom door trim. Otherwise an extremely easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrel from Kewaunee, WI
- Parts Used:
- WPW10110491
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Spark Module malfunction, won't spark
Removed back upper cover, unscrewed retaining screw from module. As noted in a comment from another do-it-yourselfer, I replaced screw with a longer one and reinstalled module. Note that the replacement part is not exactly the same as the old one(the wires are located differently), I noted the wire color codes with the slot number and reinstalled them in the same slot number. Works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James.O from Newark, DE
- Parts Used:
- WP8523178
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Lower Door Trim gets rusty
I have removed this piece once before and painted it,
but it is difficult to prepare surface.
I tried to replace the part without removing the door
but had difficulty getting the screws to line up.
So, I took the door off. Forgot that you are supposed to jam
the spring hinges in the open position before you remove the door. Manual describes how to do this but picture is not very helpful. So I made two wooden dowels about 3/8" in dia by about 3/4" long. Opened the hinge with a screwdriver and jammed the dowels in place.
Door Trim went on easily and the oven door went back on quickly.
Surprised they don't make this trim piece with rust proof material.
but it is difficult to prepare surface.
I tried to replace the part without removing the door
but had difficulty getting the screws to line up.
So, I took the door off. Forgot that you are supposed to jam
the spring hinges in the open position before you remove the door. Manual describes how to do this but picture is not very helpful. So I made two wooden dowels about 3/8" in dia by about 3/4" long. Opened the hinge with a screwdriver and jammed the dowels in place.
Door Trim went on easily and the oven door went back on quickly.
Surprised they don't make this trim piece with rust proof material.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from ASTORIA, NY
- Parts Used:
- WPW10110491
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
One of the burners was not igniting.
We replaced the part. It was pretty quick and easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from N RIDGEVILLE, OH
- Parts Used:
- WP9758079
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not ignite for BAKE. Gas would come on and igniter would "click" twice, then when burner did not light up gas went off.
Bought new igniter.
Pulled stove from wall and turned off gas and disconnected power cord.
Removed oven racks.
Removed oven floor.
Removed heat shield/dissipater thing.
Removed 2 screws holding igniter to gas burner tube.
Disconnected the wire (this was harder than expected because igniter had only a few inches slack in the wires), took off back to try to find better access to wires, no help there, door was not easily removable so difficult to reach in with 2 hands to pull wires apart, eventually I got it.
Connected new wires.
Replaced igniter to feeder tube with 2 screws.
Plugged back in, turned gas back on and tested.
Reassembled heat shield thing, oven floor, racks.
Done.
Pulled stove from wall and turned off gas and disconnected power cord.
Removed oven racks.
Removed oven floor.
Removed heat shield/dissipater thing.
Removed 2 screws holding igniter to gas burner tube.
Disconnected the wire (this was harder than expected because igniter had only a few inches slack in the wires), took off back to try to find better access to wires, no help there, door was not easily removable so difficult to reach in with 2 hands to pull wires apart, eventually I got it.
Connected new wires.
Replaced igniter to feeder tube with 2 screws.
Plugged back in, turned gas back on and tested.
Reassembled heat shield thing, oven floor, racks.
Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from RICHMOND, TX
- Parts Used:
- WPW10339442
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing a stove knob when we bought it.
Push knob onto rob.
Was this instruction helpful to you?
Thank you for voting!