WFC340S0EW0 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Norman from Newport, NC
- Parts Used:
- 814399
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
burner plug broken
Cut wires removed old plug,new plug in wire nuts on.Put heat on shrink tube done.
Less than 30 min.
Less than 30 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annie S from RIDGEVILLE, SC
- Parts Used:
- WP3148953
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner did not always reduce heat when temp. Was lowered.
My husband unscrewed the bad switch and replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Sequim, WA
- Parts Used:
- WP4314961
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
LIght switch on oven door was broken
Turned off power at circuit breaker. Removed 4 phillips screws from area over oven door. Pulled control panel out and twisted to clear top rail. Pulled two wires off of old switch.Pulled old switch through panel. Inserted new switch. Attached the two wires to new switch. Replaced panel and inserted four screws. Turned on power - it works!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from HARMONY, MN
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
temp level uneven
after watching the video, installed the temp sensor. Super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sabrina from FREMONT, CA
- Parts Used:
- WPW10196406, WPW10196405
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Used part
Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosalind from APOLLO, PA
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the oven temperature was not working right. I installed a new oven sensor. Works get now
Watch the video...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angelo from NAPLES, FL
- Parts Used:
- WPW10299224
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Active spring broken
Removed the oven door listened to a video/You tube and the rest was easy.When you remove the door panels make sure all the parts are assembled correctly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from BELLINGHAM, WA
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Replacing oven light and socket
The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William H. from morehead city, NC
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
electrical short from oven light.
I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy
Was this instruction helpful to you?
Thank you for voting!
cooktop on the rt side would just keep getting hot
Removed the ifinite controlswitch and replaced it but i dont believe it is wired correctly. now it wont get hot until it is set on four or so. think i the way it is wired.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from VERSAILLES, MO
- Parts Used:
- W11447783
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Oven got too hot with error code F6E1 (oven over temp. when heating)
I followed the instructions in the Service Technicians Guide, which came with the range.
1. replace the temperature sensor
2. replace the control board.
3 replace the wiring harness (I did not replace the wiring harness)
1. replace the temperature sensor
2. replace the control board.
3 replace the wiring harness (I did not replace the wiring harness)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHILIP from NORTH PORT, FL
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
element not working properly
Remove 2 screws inside oven holding element . Remove screws holding back panel. Plug wires (2) into new element.Install back panel . Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicki from ELSIE, NE
- Parts Used:
- WPW10196405
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Drip pans were old and with burnt on food that I couldn't get off. Disgusting!!
No problem Took off old ones and replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandeep from EDINA, MN
- Parts Used:
- W10777162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
screw came off
very expensive to buy the part but just tighten the screw intot eh predefined place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Gillett, WI
- Parts Used:
- 814399
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven heating coil snapped and would no longer heat.
It was so easy to change this out. Unplugged the stove and removed a couple of screws on mounting plate and pulled out the old heating element. Plugged in the new one and replaced the screws. Problem solved!
Was this instruction helpful to you?
Thank you for voting!