GR450LXHQ1 Whirlpool Range - Instructions

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

I refered to what I had read on repair stories of broken glass...then went to fixing mine and before I new it I was done and glass replaced...it was very easy as long as you watch what you are doing when u take it apart and replace things the same as they were removed......thank you

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I did the repair myself while my husband was at work. I lacked the brute strength to remove the door, so I ended up taking in apart while it was in place. Unfortunately, I only now noticed that instructions for installation were provided on your website. I did it without instruction, just making sure to note where screws had been removed so I'd be able to reassemble the works when I was finished. The worst part was loosening a couple of the innermost screws--even after a long soak in wd40, they were really hard to crack loose. Once I managed that, though, it went smoothly. Don't be intimidated; you can do this stuff yourself without calling--and paying--a repairman.

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

Had to screw off old terminal block & screw on new one

unscrew 3 screws under the control panel and pull that away from the glass top making sure the wires don't come apart from the connectors. care fully slide the glass forward and replace the burner which was the easy part. DO NOT try to test without making sure that none of the burner are touching the metal surface!!!!!!!! it will trip your breaker. But now we have a range with 4 burner after a year THANKS

I watched the video, purchased the correct heating element and did the repair as illustrated in the video. I simply removed the cook top, removed the ground wire, removed the wiring harness, removed the failed heating element, installed the new heating element and reinstalled the wiring. Piece of cake!

First of all I couldn't believe parts arrived next day. Parts solved the problem I was reluctant to believe new hinges would solve the problem. I installed the hinges in about 1 hour but I had door apart previously so I knew what I was doing. Now my wife is speaking to me again and she threw the wooden spoon away that she used to hold door closed. Just spent $100 dollars and saved $1600 thanks guys.

Following the various instructions here made this replacement much easier! I was able to do this on my own with just a screwdriver. Pulling the hinges out was fiddly but after removing the screw and small hinge plate from each side a little wobbling and pulling with the door open an inch did the trick. After removing the door I started with the inside glass facing up on a table, and mid-replacement needed to flip the door over. So, recommend that you start with outside of door facing up. As you remove screws keep in mind where they came from so you can replace in reverse order properly. Other than that, everything went swimmingly! Thanks to everyone for their great advice.

Sensor matched perfect, but had to pull large upper rear panel to find location. From there took a few minutes to reassemble back. Did not un hook gas but turned it off. Obviously unplugged power. Oven works fine.

Took door apart no problem had a little trouble putting it back together just one piece I put back wrong had to start over not to bad still took less then one hour

Most of the basics have been covered in previous post. I can add this- those who claim 15 minute-fixes are delusional, unless they're appliance repairmen. Secondly- what will take time is the cleaning. If you have to do this repair, which requires extensive disassembly of the door, it would be foolish not to take advantage of the opportunity to thoroughly clean all four layers of glass. Take the glass panes outside and use oven cleaner. This takes time. Other than that, the pancakeing of the components on re-assembly is tricky, but you can do it. Don

ordered replacement glass. removed oven door. dismantled parts, replaced glass and reassembled door and reattached to oven.