GR470LXMC0 Whirlpool Range - Instructions

I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate.
This was an easy fix for a seventy year-old like me!

Turn off power, remove damage knobs and element, clean up burner and scorched surfaces, order parts, when received, installed

Replaced the safety thermostat and disconnected the oven light.
Works great again...without the light

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.

1st - UNPLUGGED appliance from electrical source!! then removed screws to open ceramic stove top, disconnected wires from dead element, plugged in wires to new element, closed stove top, turned on burner - it worked!!

only problem is that "hot burner indicator" does NOT stay lit after burner is turned off!

I dismounted the oven door following the graphic templates that this site has for that model. Then I replaced the gasquet (seal window), appliying an apoxic glue to hold it on place. Then I started to put it togueter, from the bottom to the top, first the lower trim, I screwed it back to the metal frame, then the left and right trims, it goes tied by pressing it to the sides, after that I installed the top and screwed it to the frame. It holded all toguether cery well. My oven looks like new now.

Unplugged unit from wall.
Unscrewed the two screws on at he back of the oven where the element is attached
Removed old element by pulling apart the connectors.
Attached new element to the connectors.
Replaced cover with the two screws.

Unplugged the power cord first. Opened oven door and removed the two screws that held the stove top glass down. Lifted the glass top and removed the four wires connected to the element. I taped the wires to the lid in the pattern they were attached to the element. remove the element from the brackets. The new element was an exact match. reversed the sequence. Put a pot of water on and boiled a hot dog! Perfect! Great part and speedy delivery!!

Only hitch I experienced was identifying the correct replacement. The original diagram presented the accurate shape of the element my range required. However a different shaped element was displayed when I noted my unit is a series 12 serial number. I ordered it (with reservations) and as it turned out the replacement was identical to mine. Next time I will have a lil more confidence in the instructions given.

Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.

I removed the bottom drawer,unplugged the Range and pulled it out to expose the rear cover panel. Using a nut driver (a screw driver can be used), I removed the rear panel to expose the Thermal fuse located almost dead center in the back of the Range. Unplug the two wires and loosen the screw holding it in position. Replace the thermal fuse, plug the two wires into the new part and replace the rear cover panel. Return the Range to its original position and plug it in. The job is done in less than 30 minutes.

First Things first, unplug unit, remove rear cover with Phillips head screwdriver, disconnect, wires from broiler element which is the top, one, open oven, unscrew top screws first, then two at the back, wiggle out element, then reverse Steps , test repair before putting cover back on. Then ta-da, you saved yourself a $300. Service call to the appliance repair guy.

Verified via ohmmeter that one of the two burners was open and not working. I also tested the switch and that appeared to be working okay. I then took out the old unit and compared it to the new one, and found that they upgraded the new unit. I followed the instructions to match the labeled parts and move the wire to the newer location of that. i.e the old one had 2B and 2A at the top and 1B and 1A at the bottom. The new one had 2B and 1B at the top and 2A and 1A at the bottom. It did come with wire extenders and insulated tubes on top of them, and extra to cover additional. After a couple of tries, I decided which wire I needed to use on which (small connectors to match small, and large to match large.) In a second try I decided to flip it over to have it face up instead of down. Overall, it worked out very well, and I was very pleased when I did the power up test and everything worked as desired.

Remove the old part and install the new part.

Very simple.
Remove 2 mount screws using a #2 phillips screwdriver.
Pull the element out to expose the 2 wires.
Using pliers, slip both wire terminals off the existing element.
Push wires onto the new element and install both mounting screws..
Done!

NOTE: The existing element showed no exterior signs of being bad.
The damage must have been internal.