RS610PXGV2 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tom from Austin, TX
- Parts Used:
- WP4456181
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Burner "on" indicator light went out
It appears that the indicator light is a "pop-up" replacement but you can't get it to fit through the mounting hole without it breaking up...Here's the easier way: 1st remove the power to the cooktop...2nd remove the 4 burners and the bowls.. 3rd remove the 2 front small sheet metal screws that are on the front flange where you removed the front bowls...4th gently lift the front end of the cooktop whereby you'll have access to the indicator light...5th remove the 2 wires from the light and with your fingers or long-nose pliers squeeze the mounting flanges on the sides of the light and pop it out from the top...Now you can replace the light---it's "keyed" on one side so it'll fit in only one way...Reattach the 2 wires on the bottom of the light....Reverse the disassembly procedure and restore the power....Let there be "light" when you turn on any of the burners !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Noah from Richardson, TX
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
corroded, rusted drip bowls
replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from Anderson, IN
- Parts Used:
- WP4456181
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Indicator light on whirlpool electrical cook top shorted out
Removed old indicator light, after turning off electricity, installed terminals on new indicator light as I was doing this I noticed that female spade terminals had extended fastening ends on them, making an extremely unsafe condition. I replaced those terminals with insulated female spade terminals thus eliminating the possibility of a short in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derek from Sun Lakes, AZ
- Parts Used:
- WPW10207397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lower heating elememt was not working and required replacement
1. REMEMBERED TO SHUT OFF THE APPLICABLE 240V BREAKER. 2. Carefully removed the 2 screws holding the element to the oven structure 3. Carefully extracted the 2 wires from the holes at the rear. 4. Carefully removed the wires from the old element 5. Attached the wire sockets to the new element. 6. Carefully eased the wires back through the holes at the rear 7. Attached the 2 screws through the element holding clamp to the rear wall of the oven. Everything went better than I had expected.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Queen from Bryan, TX
- Parts Used:
- WPW10207397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
The bake element was not heating.
Visited PartSelect.com and ordered the element. Talked to a really sweet lady who assisted me at the company by ordering the part. Received the part and my husband cut off the electricity to the stove, took off the old element, got the sockets and after pushing on the new element, and he screwed the screws back on, cut on the electricity and we cut the stove on and it was ready to go. VERY, VERY SIMPLE TO REPAIR.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Casey from Carlsbad, CA
- Parts Used:
- WP4449259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broke the inside glass on door
Had no problem replacing the glass it took my Husband and I less than 30 min. It took only a screw driver and that's it. Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- monte from Spanish fork, UT
- Parts Used:
- WPW10207397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
would not heat up
replace thermal safety switch on back of oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Point Pleasant, WV
- Parts Used:
- WP9760767
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
I am a senior adult so the screws were a little hard to reach
With some help from my wife.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Edgewater, MD
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Drip Bowls
Lifted out the old ones and inserted the new ones and my range top looks brand new now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Viroqua, WI
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
none
I pulled out the burners, cleaned up the crumbled drip pans ,installed the new drip pans, pluged in the burners and was finished in about 3 minutes. I will order again from you. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne Marie from Albany, NY
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my drip bowls were old an I was unable to clean them
I took the old drip pans out and replace them with the new ones. Now my stove looks brand new. These were a perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Kings Park, NY
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace drip bowls
I took the old bowls out and dropped the new bowls in. No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sarasota, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
circuit breaker blew
I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Rochester, NY
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
old bowls could not be cleaned. These new bowls make the stove look great
Removed old bowls and replaced with the new bowls. Also, thanks for your help with the rang knobs. You did not have the replacement knobs for my range but you gave me help in where I might get them. With the new bowls and knobs the range looks like new. Thanks again for all your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Indianapolis, IN
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace bowls
Removed old bowls and replaced with new ones. Easy. Piece of cake. Perfect fit.thanks.
Was this instruction helpful to you?
Thank you for voting!