FES340VL1 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Burner broken
I removed the block, cut and spliced the wires to the new block and installed the burner. I used the new style block kit and saved about $30. It worked great!
Was this instruction helpful to you?
Thank you for voting!
Burners didn't work
Shut off power to the stove.
I removed the screw that held the block in place. Then I lifted the top of the rage to get to the wires. I cut the wires from the old block and stripped back the insulation. Next I put the heat shrinking sleeve on. I attached the new block with the wire nuts, pulled the sleeve down and used a hair dryer to shrink them. Then you just hook it back on screw it in and your done.
I removed the screw that held the block in place. Then I lifted the top of the rage to get to the wires. I cut the wires from the old block and stripped back the insulation. Next I put the heat shrinking sleeve on. I attached the new block with the wire nuts, pulled the sleeve down and used a hair dryer to shrink them. Then you just hook it back on screw it in and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Bear, DE
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Sockets burnt out.
Repair was very east. The suppliers package had all of the necessary parts ceramic wire nuts wire Ect. Excellent.
Will buy from Part Select Appliance again.
Will buy from Part Select Appliance again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudia from Milwaukee, WI
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My drip bowls were scorched and discolored and difficult to clean
I removed each surface coil burner from its receptacle; removed the old drip bowls and replaced with the new ones; my stove looks good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Lodi, CA
- Parts Used:
- WP77001094
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bake element did not get hot any longer
Unscrewed the 2 screws in the back of the element. Disconnected the unit from the bake of the oven, replaced the two ends of the new element and screwed in the 2 screws. Oven works great! Took less than 5 minutes to complete.
Thank you for the FAST delivery!!
Thank you for the FAST delivery!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from Farmington, MI
- Parts Used:
- WP77001094
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Bake Element Died
Had to use wd-40 to get the old part loose (oven is over 15 years old) and used pliers to pull apart from the oven. Replaced with the new part and works great. . . Once I used the wd-40 to loosen, it was super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANCES M. from GRAND JUNCTION., CO
- Parts Used:
- W10196405RW, WP660533
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken Burner
Unwrapped package. That was the hardest part. Inserted into the little spot on top of stove. Tested. Worked great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from columbus, NE
- Parts Used:
- WP77001094
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no heat element burned out
removed 2 philips screws holding element, un plugged element. new element arrive next day, insalled in less then 1 min. turned on, setoven for 375 pizza in 20 min later
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PATRICIA from JACKSONVILLE, FL
- Parts Used:
- WP77001094
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Element Burnt Out
E. G. First we turned off the circuit to the range. Then with a flash light to see we removed the two screws that hold the element in place. We then pulled the element out about 3 inches and disconnected the two wires. . . Then connected the two wires to new element and put the ends back into opening and replaced the two screws that hold the element in place. The hardest part was getting to the back of the oven for an 82 year old and a 94 year old but we got it working again!.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elnora from Brundidge, AL
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The Problem Was That The Plug Was Gone It Fell Down Out Of The Bracket
I took the old wires and plug off and replaced it with the new block it works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Birmingham, AL
- Parts Used:
- WP660532
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
burned out stove eye, 6"
remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arsenio from Beaverton, OR
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Three of four electric coils won't turn on
I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as support to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from KAMUELA, AL
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
burnt out drip pans
I had been putting off this repair for months! I finally sat down to explore ordering the parts. It was so easy - I wish I did it a long time ago. When the parts arrived, they were exactly what I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Council Bluffrs, IA
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Replace burner drip pan
Removed electric coil replaced pan and reinstalled coil. Part fit just right and no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dann from Glendale, AZ
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
reflecter/drip pans wrong size
Ordered acording to range model & such. Had ben unsucksessful gettin the right size thru the years & finally got the correct ones.
Was this instruction helpful to you?
Thank you for voting!