RF367LXKQ0 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rhonda from Logan, OH
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven was blowing a circuit.
Unplugged unit from wall.
Unscrewed the two screws on at he back of the oven where the element is attached
Removed old element by pulling apart the connectors.
Attached new element to the connectors.
Replaced cover with the two screws.
Unscrewed the two screws on at he back of the oven where the element is attached
Removed old element by pulling apart the connectors.
Attached new element to the connectors.
Replaced cover with the two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Maysville, GA
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken rear stove drawer glide
Removed drawer, after removing the 50# of junk in the drawer, Used screw driver to remove screw that holds glide to drawer and then place new part into place put screw into hole and tightened screw. Replaced drawer and told wife not to put 50# of junk back into the drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAM from DALHART, TX
- Parts Used:
- WP3195993
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The switch on the door broke. This prevented my oven from cleaning and the light burned all the time so I had to unscrew it.
First I removed the two screws that hold the glass cook top in place. Then I removed 4 screws that hold a small metal plate that shields the switch. Replacing the switch was very simply just a matter of unplugging four wire connectors from the old switch, sliding the new one in and reconnecting the wires. It was very easy to find the part on the website. I just located the switch on the diagram and ordered the part. I really surprised my husband that I ordered the part and repaired the stove by myself. He was intending on calling a repairman, but I did it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Maple Grove, MN
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Rear Drawer Glide
This was a very smooth repair. In total it took about 5 minutes. The pot drawer below the oven wasn't gliding like it once did. After I replaced the glides it works like new. Please note, if you are going to replace one side go the next step and replace both to provide balance to the drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from PLUM CITY, WI
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven not keeping correct temp and sometimes would not relight when temp went dropped.t
Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RUSSELL from LEESBURG, FL
- Parts Used:
- WP3149400
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
large right front burner wasn't going on
turner off circuit breakers for range, i rolled the range out from between counter tops so i could see the burner sw. using a flash light read all the numbers on the switch to my wife who wrote then down, knowing what the switch looked like i could find could find correct instruction video on parts select & check the switch numbers & ordered it. replacing- made myself a drawing of the wiring connections, replacing switch-power off, unscrewed mounting bracket, removed switch, removed ONE WIRE AT A TIME & CONNECTED IT TO SAME TERMINAL ON THE NEW SWITCH, remounted the switch & turner on circuit breakers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from BEND, OR
- Parts Used:
- WP3149400
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
This burner on our range had no temperature control - it was either full-on or full-off
1. Pull range out from wall
2. Unplug range
3. Remove back cover using drill and screwdriver bit
4. Remove dial handle on affected burner dial
5. Remove two screws to unattach broken infinite switch
6. Disconnect wires from broken infinite switch
7. Reconnect wires to new infinite switch
8. Attach new infinite switch using two screws
9. Use pliers to snap off end of post to fit your burner dial, if necessary. It was on ours.
10. Reconnnect dial handle.
11. Reattach back cover using drill and screwdriver bit.
12. Plug range back in
13. Relocate stove against wall
2. Unplug range
3. Remove back cover using drill and screwdriver bit
4. Remove dial handle on affected burner dial
5. Remove two screws to unattach broken infinite switch
6. Disconnect wires from broken infinite switch
7. Reconnect wires to new infinite switch
8. Attach new infinite switch using two screws
9. Use pliers to snap off end of post to fit your burner dial, if necessary. It was on ours.
10. Reconnnect dial handle.
11. Reattach back cover using drill and screwdriver bit.
12. Plug range back in
13. Relocate stove against wall
Was this instruction helpful to you?
Thank you for voting!
Broken drawer glides
Simply removed the bottom drawer, unscrew the old broken glide, and attach the new glide. Simple and no hassles.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- corey from SHAKER HEIGHTS, OH
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Sparks flying out of the oven, broiler element melting
First Things first, unplug unit, remove rear cover with Phillips head screwdriver, disconnect, wires from broiler element which is the top, one, open oven, unscrew top screws first, then two at the back, wiggle out element, then reverse Steps , test repair before putting cover back on. Then ta-da, you saved yourself a $300. Service call to the appliance repair guy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from SAN FRANCISCO, CA
- Parts Used:
- WPW10118455
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Exterior glass of oven door broke spontaneously
We cheated; a local appliance repair company was called & the tech guy repaired it in 10 - 20 minutes. Couldn't be happier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from CAMDENTON, MO
- Parts Used:
- WPW10202217
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven handle broke
new handle arrived black for white oven - screws did NOT fit new handle- glass came off the door when removing old handle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alexander from LINCOLN, NE
- Parts Used:
- WPW10308477, WP3196174
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Bake element was broken
Remove the old part and install the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from LANCASTER, SC
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking element had burned into
The video was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilton from CANYON LAKE, TX
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven bake would not heat up at all.
Very simple.
Remove 2 mount screws using a #2 phillips screwdriver.
Pull the element out to expose the 2 wires.
Using pliers, slip both wire terminals off the existing element.
Push wires onto the new element and install both mounting screws..
Done!
NOTE: The existing element showed no exterior signs of being bad.
The damage must have been internal.
Remove 2 mount screws using a #2 phillips screwdriver.
Pull the element out to expose the 2 wires.
Using pliers, slip both wire terminals off the existing element.
Push wires onto the new element and install both mounting screws..
Done!
NOTE: The existing element showed no exterior signs of being bad.
The damage must have been internal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from MIDDLETOWN, CT
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Old lower element fell apart
1. Unplug the power
2. Unscrew the two screws that hold the element
3. Pull the element out a little to expose the wires.
4. Gently pull off each wire (best done with needle nose) MAKE SURE THE WIRES DONT FALL INTO THE BACK OF THE OVEN.
5. Firmly seat wires back onto new element and replace screws
6. Bake stuff!
2. Unscrew the two screws that hold the element
3. Pull the element out a little to expose the wires.
4. Gently pull off each wire (best done with needle nose) MAKE SURE THE WIRES DONT FALL INTO THE BACK OF THE OVEN.
5. Firmly seat wires back onto new element and replace screws
6. Bake stuff!
Was this instruction helpful to you?
Thank you for voting!