SF362BEGQ0 Whirlpool Range - Instructions

Take off the back panel of stove and unplugged timer motor and switch on door latch assembly,removed two screws that hold assembly and slide rod off. I put 110 volt plug to timer motor and it did not move, that is how I diagnosed problem. Ordered new assembly (cannot buy just timer motor)put new door latch assembly on and worked fine. Of course unplug stove before you start !

Very easy. A couple of screws and it was repaired. Parts select makes it easy and affordable to do minor repairs on my appliance. This is the second time we have used this company to repair our oven and so far all has gone very well.

ordered the part and in less then 24 hours from ordering the part it was shipped and delivered and my husband and I put the part in took us no time at all very easy to do... 2 years ago i had this same problem and called a guy in the area cost me $200. I had dinner in the oven by 5 that night!!!!

Really quite simple. Remove the racks - remove the two screws in the back of the bottom plate - slide out. remove the bottom drawer. remove the two screws holding the igniter - unplug the old igniter and remove. screw in new igniter, plug up new igniter, replace bottom drawer, replace bottom pate, replace racks. I did turn off the gas and electricity to the unit before repairing - and it was easier for me to get behind the unit to unplug/plug the igniter. works great! thanks!

We ordered our part from PartSelect.com, of course, using their diagnostic tool(s). We received it very rapidly after ordering (a day or two). It involved taking two screws out of the bottom plate of the oven. There were two screws in the diverter (?), but they weren't attached to anything. I had my son, who is young, strong, and small get behind the oven to locate where the igniter plugged in. He detached it and I unscrewed the nuts holding it in place. One of them was in pretty crooked and made it a little difficult. But I pulled it out. I put the new one in place, my son plugged it in, and I replaced the two nuts, securing the new one in place. I replaced all the parts and their screws while the wife cleaned the gunk from behind where the stove sits. We did perform a quick test prior to re-assembly and it looked good. Re-attached everything, put it back in place and it's working like a dream. Just in time for Fall baked goods...

Removed bottom plate by pulling up from the back (had some resitance), Two machine screws holding cover over igniter, used 3/8" socket to remove. Pulled oven from wall to disconnect igniter @ coupler, unscrew one more machine screw, fed replacement igniter into slot and coupled, attached single screw to pipe, put cover w/ 2 machine screws on top, install bottom plate. Had to use butter knife to get bottom plate to fit into the front cabinet area of stove. Done & working fine.

most difficult part was having to pull the stove out to access the Igniter wire connector. unplugged connector, removed 2 Igniter mounting screws, installed new Igniter and connected plug. very easy project. less than 30 minutes total thanks to website for perfect diagnosis of problem

First time was very difficult I tried to make the panel fit into the frame. Broke both side pieces of the trim.Even thouth I broke the trim PartSelect replaced them. I did not expect that.Second time it was easy. Remove the handle first and then the panel slides into the top and bottom only. It does not slide into the side of the frame but sits on top of it. Thanks, Allen

Remove the bottom drawer. Remove the two Phillips head screws on the top inside of the door. Pull up on the handle (CAUTION: Be sure to hold the glass front against the door while doing this or the glass front can fall, possibly damaging it. Remove the glass front by lifting it towards the top of the door. Remove the two side pieces and the bottom trim piece by unscrewing the Phillips head screws located on the underside of the bottom trim piece. Discard the old trim pieces. Attach the new metal bottom trim piece using three of the previously removed screws. Do not tighten the screws at this time. Each plastic side piece has a nipple at the bottom. Insert this nipple into the outermost hole at each end of the bottom trim piece. The edge of the flange on each side piece should face inward. Have an assistant hold the two side pieces against the door frame while you slide the glass back in. The inward facing flanges go UNDER the glass. Reinstall the top piece making sure the indentations at the top of the side pieces are under the top piece. Install and tighten the two screws that hold the top piece on. Tighten the three screws holding the bottom trim piece.

To begin with,the symptoms were strange.....the burner would not ignite even though the igniter was glowing....but if you bumped anything in the broiler or pulled the drawer out and closed it abruptly,it would lite. This went on for a few weeks , until slamming and banging worked no more.(that was getting old anyway)I went ahead and ordered the igniter.It came fast and was very easy to replace.I went in from the oven,took out the racks and the bottom plate(2 screws), exposing the flame diverter that is just above the burner.(2 screws)You can access the igniter now ,and remove it.(2 screws),and unplug it.Reverse order to install the new one.I didnt unplug the range or turn off the power,because I screwed the igniter on first and then it was a matter of just plugging it in. Everything went back together and turned on the oven. Worked fine. Very easy to do,and no more banging around the broiler.Should have done it sooner.

I removed the oven racks, removed the oven floor and the oven burner cover, pulled the range out and removed the small panel on the back which covers the igniter connector. I disconnected the old igniter, removed the two screws holding the igniter in place and removed the old igniter from the oven. Then screwed on the new igniter, fed the wire through to the back and connected the new igniter. Turned on the oven and voila' we have ingnition! The oven is working again but I'm getting the "F2" routine sometimes. It doesn't do it every time but when it does I unplug and replug and then it works. I'm a 67 year old female and I considered it very easy so pretty much anyone should be able to do this repair.

The malfunction was narrowed down to the oven door motor lock, located at the upper left back of the unit. Removed two panels from the back of the unit, 8 screws. Then the motor, 2 screws, 4 wire connectors. Reversed the procedure for the installation, and solved the problem. About 30=35 minutes for the job. If your handy at all, it should not be a problem.

I pulled the stove out from the wall & took the back lower right cover off. Unplugged the power cord & disconnected the igniter from the power. Took shelves & bottom cover (took two screws out)from oven. Used nutdriver to remove old igniter, then pulled the connector through into the oven, discard. Put new igniter in place with nutdriver.Push connecting cord through to back of stove.Replace bottom cover & shelves. Plug cords together & plug cord back in to outlet.Turn stove on & igniter works!!! Push stove back into place & bake a cake! :)

Removed back of stove, 8 screws, removed original latch assembly and installed new assembly. One thing that can cause you difficulty is that the rod that connects the assembly to the front latch on the door can disconnect and has to be reconnected.[Problem]

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.