SF362BEGQ0 Whirlpool Range - Instructions

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I took apart the bottom of the oven to see the ignighter. I moved the oven away from the wall and took off the metal plate that covers the ignighter electrical connection.Unplug the old part and plug in the new one. With the nutdriver remove the two screws holding the part onto the gas tube. Save the screws and attach the new part with them. Turn on the oven to see if the gas tube lights. If all is good put the metal plate on the back of the oven and replace the other oven parts. Make biscuits!!

Unscrewed the feet from the floor. Pried up the range top, removed burners. Unscrewed sides of the range from wooden cabinet it was recessed into. Unplugged range from outlet. Pulled range out into the open. Removed back cover. Discovered that I have the wrong replacement part.

Loosened two screws and removed tray, very simple. Replaced new tray and adjusted screws to hold tray. Easiest part was finding new tray part number and ordering replacement using online parts diagram.

Remove the side covers. Remove the 2 screws on the back side of the door, hold on to the glass and front panel, they will fall out. remove the 2 screws holding the handle. Put the new handle in place and insert screws, note the old handle had metal inserts that are threaded, the new does not. Had to push very hard and let the screws bite into the plastic.

new handle arrived black for white oven - screws did NOT fit new handle- glass came off the door when removing old handle

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

Unplug range from electric service.
Turn off gas supply to range.OVEN
Removed the floor panel of the oven housing.
Unscrew,and removed the heat deflector. (Caution sharp metals)
Used 3/8 socket set to unscrew the old Igniter, used same bolts to mount new Igniter.
Go to the back of the range removed the metal guard held by four Phillip screws, unplug old harness, plug new factory plug (do not alter harness)

DISCONNECTED POWER AND GAS TO THE RANGE. REMOVED 6 SCREWS FROM REAR OF THE RANGE. REMOVED THE 2 SCREWS HOLDING THE TEMPERATURE SENSOR IN PLACE. DISCONNECTED THE LEAD FOR THE SENSOR. INSTALLED NEW SENSOR IN REVERSE ORDER. OVEN WORKING PROPERLY NOW.

Only one screwdriver needed for this simple repair. Unfortunately for me it did not repair my oven and a new code on the oven indicated a bigger problem with computer board.
Part Select was great to work with and accepted a return and promptly refunded me for the part.
Thank you!

Loosen 2 screws and put new part in and tighten 2 screws. After putting in new sensor stove gave me another code had new part in 5 min and part select would not take my part back.

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy