RF361PXKT1 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edward from Crimora, VA
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Block broke
Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Caddo Mills, TX
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Inside Light would not work
Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from palm beach gardens, FL
- Parts Used:
- WP179051
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
range handle fell off and screw got lost
It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Port Orange, FL
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door glide broken
removed the old ones.then installed the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Negaunee, MI
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.
Took off the screws on the back of the stove and took out the sensor, and put in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from windsor, VA
- Parts Used:
- WP3148952
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
water pump went out
it was very easy i took the pump off only two clips and two hoses holding it type in the model number at parts select it came right up soi new it right one from the picture got with in 3 days put it back on less then 10 mins
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Maryland Heights, MO
- Parts Used:
- WP3195546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The front drawer glide broke
Very easy. A couple of screws and it was repaired. Parts select makes it easy and affordable to do minor repairs on my appliance. This is the second time we have used this company to repair our oven and so far all has gone very well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charlie from glenwood springs, CO
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven was not heating up to temp.
Pulled the oven away from the wall, unplugged the oven. Unscrewed the back panel(2 screws)that covers the pigtail connection. Pulled the two wires that attached to the heating element. Inside the oven i removed the two screws holding the element in place and removed old element. Put the new element in place and returned screws. The two wires clipped effortlessly on the back, returned cover and screws and plugged the oven back in. Tested the oven and returned it to its position, reset the clock and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Voorhees, NJ
- Parts Used:
- WP3196231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob broke and others were loose.
Thank you. Have been looking in stores for knobs to no avail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANTHONY from HOUSTON, TX
- Parts Used:
- WP3196231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner knobs broken
Pulled old knobs off and replaced with new knobs from PartSelect. I'm glad they had them, no one locally had them available.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy Scott from Tupelo, MS
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The heating element had burned through from food spillage and sticking
I removed the broken heating element while waiting for the new part to arrive and cleaned the oven. SO much easier without anything in the way. Once the part arrived and it was wonderfully packaged...Easy to open but very well protected, it was a snap to connect the 2 power wires and then screw in the 2 screws to secure the heating element. I was back to baking in less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eloy from Andrews, TX
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element not working
Turn power off at breaker box, remove back cover inserted wires into element, done and ready to be use
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia M from Houston, TX
- Parts Used:
- WPW10308477, W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
elements (bake and broil) needed to be change out
unscrew the bolts connecting the elements and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Odenville, AL
- Parts Used:
- WPW10308477
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Bake element replacement
Keep in mind that I am a 65 year old woman who has replaced bake elements on a much older range that was hard wired. I viewed the video so I knew what to expect. The job would have taken no more than 15 minutes if the retaining screws had not been stuck. After several doses of WD40, I finally managed to get them loose but only then after I had tried every screw driver in the house. I clamped the leads with vise grips to keep them from slipping back in the stove. Unplugging the old broken element and plugging in the new one took maybe a couple of minutes. The retaining screws went back in without a problem.
Was this instruction helpful to you?
Thank you for voting!