RS676PXV1 Whirlpool Range - Instructions

Used screwdriver to unfasten the old element from the oven frame. Then unplugged the two wire plugs from the back of the old element. Reversed the process to install the new. Couldn't have been any simpler.

First I made sure it was in fact the lower bake element that was broken. I turned the oven on & noted the element did not glow red. I also used a laser thermometer to verify the element was at "room temperature" for the room it was in (the oven - about 200 degrees, given what the upper bake element was contributing.)
And close visual inspection showed that a section of te bake element had melted thru where something had recently spilled onto it.
Swapping it out was easy - turn off the electrical breaker controlling the oven, unscrew the bake element, disconnect the electrical contacts to it (which required pliers, since they had been on a Looong time, and a little care to not use the pliers too hard & thus break the wires or contacts), then reverse the process to install the new element.

It works great now.

Simply remove two phillips screws, unplug and replug. Thanks to the quality parts I bought here it saved me $65.00 on the part alone. Locally $85.00 plus shipping.
Thanks guys for your help.

Removed the two sheet metal screws holding the element, Unplugged the contacts and plugged and fastened the new element.

removed the old one replaced the new one every thing works like new. THANKS

Made sure that "Breaker" for oven is in the off positon.

Opened oven door to the first "stay open" position...lifted door straight up...and off of the hinges....which removes the door....and allows easier access to oven.

Removed oven racks

Removed two philips head

Pulled burned out element toward the front of the oven.....exposing the two connector wires.

Used pliers to pull wire connectors from burner element connectors.

Reversed the order of this process....to install new element.

On Saturday night before Thanksgiving my Wife indicated the oven was not heating up. A quick continuity check of the element indicated the unit was burnt out. I got on line and found PartSelect, found the proper element and ordered it. On Wednesday the element arrived and I removed the oven racks, removed two screws and pulled out the element to access the terminals. disconnected the wires, reconnected the wires to the new element and reinstalled the screws. Entire time was less than 5 minutes.

Thanksgiving dinner was saved at a reasonable price.

Unscrewed the two screws that held the old element to the back wall of the overn. Pulled out to reveal the two wires and connectors. Disconnected the two wires and removed old element being careful not to let the two wires recede back into the wall of the overn. Took the new element and connected the two wires. Then screwed the two screws through the holes in the element into the back wall. Easier than I thought it would be.

simple replacement

turned power off Unscrewed 2 screws pulled old element out slightly . disconected wires . connected wires to new element tightened 2 screws turned power back on baked a pie. took longer to type this

i received the part via fed-x i opened the box uninstalled the old part installed the new part turned it on the element got red hot and it works just fine.

Turned off electric to oven by shutting circuit breaker.Opened oven door, took out baking racks,loosened bolts from rear of oven holding element and plate . Disengaged element with plate from wires at rear of oven. Attached new element to clips on wires, rescrewed element plate back to rear wall. replaced racks and turned on circuit breaker. DONE!
Thanks for the quick service ordered one day, next day delivery, never missed a meal or dessert.

1) Turn off the power at the circuit panel!
2) Remove 2 screws at the back of the bake element.
3) Gently pull the element out about 6 inches.
4) "Unplug" two wires from the back of the element.
5) Do the same in reverse to put the new element back in.
6) Turn the power back on.
7) Done!

I order the part on 7/29 and much to my surprise, it arrived the very next day. It took less than 15 minutes to remove the old element and installed the new one. It was a little difficult to unplug the old one and took quite a bit of pulling but it came out okay. Plugging in the new one and screwing on the cover plate was easy.

Unscrewed two screws, pulled the element out of the socket, pushed in replacement element, screwed in the two screws--done!