SF303PEGQ1 Whirlpool Range - Instructions

I removed the bottom srtip. Installed the new bottom strip, snapped in the side pieces. [The old ones screwed in.] Replaced the original handle. Ready to reinstall door.

Found that the two screws securing the bottom had rusted away allowing me to just lift the old bottom out. The new one fit in place exactly and really did not need the screws. Done in 2 minutes.

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

remove the hinge stays they just clip in
remove the door. took out screw at bottom of door.
replaced trim.
replacing the door was a problem i didn't have pins to put in the spring loaded hinges so i used nails to hold hinge in position.
so make sure to open oven door first insert pins or nails in hinges then remove door. It would have took 10 min. to do.

First I Pulled the oven away from the wall and turned off the gas and unplugged the oven. I then removed the bottom drawer and the oven door to get easy access to the ignitor location. I then removed the oven racks and the 2 shields which cover the ignitor with a screw driver. I then removed & unplugged the ignitor and 2 screws holding the ignitor in place. This all took about 15 minutes. I then reversed the process and installed and assembled the oven. It only took about 25 min in total time and low and behold the oven worked again. Amazing the technology stuff. My wife things I am a genius...again. Not!!!

Remove 2 screws holding oven bottom in place.Lift out the plate and replace with new plate. The hardest part of the replacement was lining up the screw holes. By the way i have never received such great service from any internet company as Part Select. I ordered the part on a Monday and the part was at my home the NEXT DAY and installed that evening.

Removed two screws holding the bottom in, pulled out old bottom, inserted new bottom, replaced screws and tightened them. Total time less than five minutes.

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed two screws and the front of the door popped off. Replaced the bottom metal piece that the glass front slides into. It was a piece of cake.

Replaced bottom trim included in kit.
Installed side door trim.
While trying to slide glass front in place both plastic side trims broke.
Had to use already broken door trim and glued in. Just hope when use oven glue doesn’t melt and will have to replace entire oven.

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.

Removed bottom pan from oven, removed gas flame deflector to expose ignitor and burner. Saw that ignitor was not working. Removed two mounting screws, pulled ignitor and wire until wire nuts were exposed and disconnected ignitor. Replaced with new ignitor, bracket and wire nuts. Remounted the new ignitor, and tested burner. Worked ok. Reinstalled deflector and pan, back in business.

I read some of question & answer to the problem I was having with the oven. When I saw do-it-yourself that all I need to know. Repair man quote me for 100.00 dollar he will do it plus part. So I save 100.00 dollar and done it myself. Thank to partselect for fast and quick delivery service. It was only 2 screws holding the element and the connector was a just plug it into the other plug very easy to do. I will always come back partselect for answer and help and buy the part from them. YOU ROCK PARTSELECT

I still don't have it back together! The first time we ordered the part the gentleman sent me the trim for the left side which seemed to be fine but while replacing it the old part (right side) broke. Ok. so I called to order same part but for the right side. Well, the lady told me I could only order the oven door trim kit, which seems to be too large. I don't think she understood me. Why the 1st time ordering I could get the left side only now when ordering the right side she says we don't sell it that way. Very confused and still can't use my oven since Dec,19th!!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.