FES355YL0 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Johnson from Norwood, CO
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element Failed
I had previously partially removed the element and tested with multi-meter to determine that it was not working (open circuit). Repair procedure follows:
Turned off Power
Removed 2 retaining screws
Pulled element out part way
Removed 2 spade connectors supplying power
Replaced element w/new element
Reversed procedure
Tested Oven; worked fine.
Turned off Power
Removed 2 retaining screws
Pulled element out part way
Removed 2 spade connectors supplying power
Replaced element w/new element
Reversed procedure
Tested Oven; worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Sequim, WA
- Parts Used:
- WP4314961
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
LIght switch on oven door was broken
Turned off power at circuit breaker. Removed 4 phillips screws from area over oven door. Pulled control panel out and twisted to clear top rail. Pulled two wires off of old switch.Pulled old switch through panel. Inserted new switch. Attached the two wires to new switch. Replaced panel and inserted four screws. Turned on power - it works!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Milford, MI
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner inop
removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy and quick repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from Spooner, WI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element went bad, will not work.
As soon the Bake Element has arive, I install it no more than 5 min... All I nedd was a Screw driver. It was so easy, Thank You PartSelet!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brenda from las vegas, NV
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom element burnt out
removed 2 screws . pulled out the 2 wires and disconect them. took out the element. Put the new element in and hooked the wires up. placed the metal bracket to the back and put in the 2 screw and turned it on and it worked like new.
Brenda
Brenda
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Veronica from Brunswick, GA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom element was burned out
I removed two screws, pulled it out a few inched and unpluged two wires. I then plugged the two wires into the new element slowly slid the wires and element back into place and put the two screws back in... and it worked perfectly. I did it all in less than five mins. And I am a 53 year old woman.No man was required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from South Burlington, VT
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not heat up
Just like you said,remove two screws,pull out element,disconnect wires,install new part. It was easier to pull out stove and hook up wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W Robert from Downers Grove, IL
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old element arced bigtime so we figured it was time - 18 years old!
I read other other posts and followed their advice. Remove the 2 screws holding the element to the back of the oven...gently pull it out about 3" to reveal the connecting wires. I found the needle nose pliers were necessary to detach and reattach the wires. Don't yank! Be aware that the wires have a tendency to want to pull back into the back of the oven while they're loose. This was a wall oven and that woul've been a large problem if they they had. Otherwise it was a snap!
Was this instruction helpful to you?
Thank you for voting!
burners wasn"t getting hot like they should
i just unpluged the old burner and slideed the new burners in place and they work great now like a new range
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Arlington, NE
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
When the oven was on we noticed the bake element had a 1 inch section that was bright red. Upon closer inspection, after the oven was off and the element cool, corrosion like damage was apparent where the element had been bright red.
Naturally the oven turned was off but for added safety I also set the breaker protecting the oven to the off position. Where the element attaches to the oven there is a small plate with two screws holding the element in position. Remove these two screws and then gently pull the element out 2-3 inches, which will expose the electrical connection. Using needle nose pliers gently pull on one of the wires to remove it from the element. Now remove the other and discard the old element. Simply plug the new element into those wires and screw the plate back into the oven. Now turn the breaker back on and you're done. Super easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heriberto from AUSTIN, TX
- Parts Used:
- WP8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
THE OVEN WAS NOT HEATING TO DESIRED TEMPERATURE
DISCONNECTED POWER AND GAS TO THE RANGE. REMOVED 6 SCREWS FROM REAR OF THE RANGE. REMOVED THE 2 SCREWS HOLDING THE TEMPERATURE SENSOR IN PLACE. DISCONNECTED THE LEAD FOR THE SENSOR. INSTALLED NEW SENSOR IN REVERSE ORDER. OVEN WORKING PROPERLY NOW.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Redding, CA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven element caught on fire!!
My husband is an over-the-road driver, so I have to do all of the repairs myself. I went to the breaker box and turned off the power to the range. Then I removed 2 screws, pulled the element out about 3", and disconnected the wires. I then connected the wires to the new element, pushed it back in place, and replaced the screws. We had Parmesan Chicken for dinner and my children were thrilled!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from YONCALLA, OR
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Heating element had a melt down and small explosion
Remove racks, extract two phillips head screws, pull out element, unattached wires, install new element, reverse procedure to complete installation. (Note: With the racks and element out, great time to clean oven.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from MIDDLE RIVER, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element burned out
Turn off the oven circuit breaker. Remove 2 screws that hold the element in place. Carefully pull element out, about 3 inches and remove 2 attached wires by holding the element and pulling the wire clips off of the old element. Slide wire clips onto the new element and put the screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from Chesterfield, MO
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
old heating element "popped"
Ordered the part Friday afternoon. It was delivered early on Saturday afternoon. Very impressed with the speed of the delivery! Power off, unscrew the old part, replace, screw the plate back on. Easy!
Was this instruction helpful to you?
Thank you for voting!