GW395LEGB6 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- doug from ramsey, IL
- Parts Used:
- WPW10110491
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burners would not lite, no spark
pull out the stove,took the top back panel off, take off wires one at a time on new spark module.. easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Chicago, IL
- Parts Used:
- WP9782065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Kitchenaid gas oven would not heat
The stove burners and oven broiler worked fine so it was obviously something with the oven ignition. My oven is 14 years old so it made sense that the ignition would wear out. I followed the instructions provided on the PartSelect website for this repair and it worked perfectly. Very easy fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chapel Construction from Caledonia, WI
- Parts Used:
- WP9782065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Range was operating intermittently.
The repair was so easy. The part came in a box and as I expected it was an exact match. I closed my eyes...counted to three and behold the part was installed. I don't think that installation could have gone any better. I would buy again from this company if I needed parts for any appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Gettysburg, PA
- Parts Used:
- WP9782065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not light.
Open oven door. Remove covers from burner tube. Remove 2 screws holding igniter. Remove panel from back of range. Unplug 2 wires attached to igniter. Pull wires thru inside of oven. Reverse process to install new igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Houston, TX
- Parts Used:
- WP9782065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven would turn on but not heat
Looked online and found it was probably the igniter which wasn't firing. An incredibly gratifying and easy experience with the self-fix. Worked on the first try just like new.
Was this instruction helpful to you?
Thank you for voting!
broken interior glass in door
pulled door up and out. Disassembled door. removed old glass and rope gasket. installed new glass and gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Fort Wayne, IN
- Parts Used:
- WP9781593
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The inside oven glass cracked down the middle
I was able to remove the door by opening it partially and lifting it up while jiggling it. Once off, I laid it with the inside up on a table and the screws along the bottom facing outward so I could access them easily. I removed the various screws and porcelain covers and sides feel of easily. The inside panel lifted off exposing the inner glass and frame. The screws and clips had to be sprayed with penetrating oil to remove them. The frame lifted off and the cracked glass was removed. I was careful to wipe away all the fluid used to loosen the frame clips. Assembly was the reverse of this being careful to let pieces fit nicely without force. It would have cost me $39 to have the repair performed assuming I could get the door off. A Phillip's head screwdriver was not adequate to remove the frame clips. You needed a correctly-fitting square drive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Woodinville, WA
- Parts Used:
- WP9782065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven would not heat up/slight smell of gas
Replacing the igniter took care of the problem. I just wish I had made better notes about how the wire were routed. It would have saved time as I re-assembled everything. Th ejob itself was really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Melbourne, FL
- Parts Used:
- WP9781593
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Inner Oven Door Was Cracked
Step 1. Always ensure appliance is unpluged from power source. 2 Remove oven door by open slighly and lift up be sure your hands are up from hinges they can snap back and injure fingers. 3. Have a cover on a flat surface and have a diagram of oven door, 4. Remove bottom screws and slide out top glass and side rails. 5 Remove top cover and insulation over glass. Beware of any jagged glass. 6. Incert new glass. 7. Be sure when replacing insulation and cover that cover in under tabs to ensure glass is firmly held in place repeat steps in reverse order. Took just 20 minutes to repair. I used a small electric screw driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from Colorado Springs, CO
- Parts Used:
- WP9781593
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My inner glass on the oven door got cracked from spilling something cold on it, while it was hot.
Removed the door. Took out all the screws. Removed the glass that was cracked. Put in the new piece. Put the screws back in place. Put the door back on and it was a done deal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clarke from San Diego, CA
- Parts Used:
- 9782081
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not heat past 170 degrees
Pulled the oven out from the counters and unplugged the electrical cord. Unscrewed the three screws holding the center back panel on and removed the panel. Located the temperature probe in the upper left part of the oven and followed the wiring to where it was connected. Unconnected the wire from the connector. Removed the screw holding the probe and pulled it out from the oven. Put the new part on and screwed it to the oven. Connected the wiring to the connector. Put the panel into the holding brackets and screwed in the three screws. Plugged in the oven and put it back against the wall. Turned on the oven, set a temperature and watched to see if it stopped at the set temperature. Bake3d dinner and ate it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from Sandusky, OH
- Parts Used:
- 814229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Drawer Roller Snapped Off
Replaced both rollers....Quick and Easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Oakton, VA
- Parts Used:
- WP8053456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced a stove burner grate
No tools necessary. Shipment was extremely quick; I was very pleased.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph W from Anaheim, CA
- Parts Used:
- WPW10447925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner Grate coating was damaged
Remove old grate and replace with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Plainview, NY
- Parts Used:
- 814229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheel broke off oven drawer
I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in
Was this instruction helpful to you?
Thank you for voting!