RS610PXGW8 Whirlpool Range - Instructions

Unlocked the latches that hold door into oven. Removed door to work on it. Disassembled door by removing all the screws that hold it together. Removed two other glass sheets to access location. Cleaned out broken glass. Installed new glass sheet and reinstalled two other glass sheets. Reassembled door and reinstalled in oven. Not difficult, just a fair number of parts and pieces to take apart and put back together.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

took out door hinges, slightly close door, lift upwards, remove clips on bottom of door, remove screws from 2 inner layers of glass, insert new glass, perform revers order reassembly..cleaned all inner glass, and surrounding parts prior to reassembly

Removed the door from the unit. Set the door face down on a work surface. Remove the screws and put them in a separate place from the rest of the screws (They are a different style of screw). Turn the door back over. Remove the two clips at the bottom on the door. The door front will slide down. Set the door front off to the side with the two clips and the screws. Remove the screws securing the brackets for the next level of glass (Mark which it the top and which is the bottom bracket. Place the glass, brackets and screws together. Remove the next glass/bracket assembly and set it aside with the screws. Lift the inside metal glass retainer and set it aside. Remove the old glass and install the new glass and reverse the order of the disassembly process.

It appears that the indicator light is a "pop-up" replacement but you can't get it to fit through the mounting hole without it breaking up...Here's the easier way: 1st remove the power to the cooktop...2nd remove the 4 burners and the bowls.. 3rd remove the 2 front small sheet metal screws that are on the front flange where you removed the front bowls...4th gently lift the front end of the cooktop whereby you'll have access to the indicator light...5th remove the 2 wires from the light and with your fingers or long-nose pliers squeeze the mounting flanges on the sides of the light and pop it out from the top...Now you can replace the light---it's "keyed" on one side so it'll fit in only one way...Reattach the 2 wires on the bottom of the light....Reverse the disassembly procedure and restore the power....Let there be "light" when you turn on any of the burners !!!

INNER GLASS - A YouTube video on removing Whirlpool Oven Doors was very helpful. Cleaning the other two panels of glass with a Baking Soda paste worked like a dream. Re-assembly was fairly easy. The hardest part was re-aligning the outer glass cover's top holes so I could drive the screws in. LIGHT BULBS - To easy to describe.

I lifted the door from the oven. I reviewed the break down of the parts. The only tool needed was a screw driver to disassemble the door. I stacked each part in the order it was removed and replaced them in reverse order. PS, I cleaned the old glass before it was reinstalled it.

Had to screw off old terminal block & screw on new one

First thing you must do is remove door from oven, to do this there are locks on the hinges, lift them up. Next put door into an upright position with door opened about two inches, lift up and pull away from oven. Lay door on flat surface with inside of door facing up. there are two screws at to of door and two screws at bottom of door remove them place to side. next there are four more screws on each corner of the inside of door, they also need to be removed. this will cause the inside and outside of door to come apart. Hold door together and flip over, be careful. remove outside of door put to side. there is a bracket at the bottom with two screws remove, and remove bracket. There is a bracket at top with one screw remove. there are two pieces of glass be careful remove the two pieces of glass to get to the broken piece. Clean broken glass be careful not to cut yourself. Remember how you removed everything to put back together, do everything in reverse. Good luck, it's not that bad.

Instructions were clear and the work was easy. Take your time and think about what you are doing, and you won't have any problems replacing the glass.

This 60 y.o. female had no owners manual. I completely relied on the information of this forum. *Recommend having a work area prepped before starting. I used a thick beach towel on the kitchen table. A layer of newspaper to catch all the dirty bits is a good idea.*You must remove the door - I followed the instructions using the allen wrench in the holes of the hinge. Open door. I put the short end of the wrench in the hole and leaned the long end against the oven rim. Start closing door and when almost closed, lift up to remove.*Place door handle side up on work surface to remove the 4 screws that hold outermost glass in place, 2 at top and two in brackets at bottom. Lay this aside in safe place on table. *Take off each layer to reach broken glass. *The hinge assembly has to be removed and the allen wrenches have to come out in order to accomplish this. Squeeze the hinge to take pressure off wrench to remove. Gloves help protect your hands for this step.Remove 2 screws each side. Keep each hinge next to the side it came from so you reassemble correctly.*If you have a phone with photo capability - I recommend you take a photo of each disassembly step. This saved me when it came to replacing the two brackets that hold the inner two pieces of glass. Clean all parts before reassembly (this takes the longest amount of time). I placed a thick cup towel in my sink and scrubbed. The cleaner I use for my glass range surface worked best. Dry thoroughly. When you get to the shattered glass remove it very carefully to avoid damaging the insulation underneath. I wish I had just purchased replacement insulation. Once the glass is replaced, everything goes back in reverse order. Now, here's the thing. I spent alot of time scrubbing. So, by the time I got to reassembly, I was bamboozled by the two 10 inch aluminum brackets that hold the two inner pieces of glass in place. So, to avoid any confusion, pay close attention to how these two brackets are placed or take pictures. This was an easy fix that went really well thanks to all the helpful info found here.

find the owner's manual & follow the instructions for inserting two allen wrenches (assuming that you cannot find the "removal tools" that came with the oven) into the holes near the hinges on the door, carefully & slowly close the door with the wrenches inserted until the hinges disengage from the wall mounted oven. Lift the door away (is rather heavy). It is necessary to remove panels from the front one layer at a time to reach the 3rd layer of glass (the inner most glass that is the rather easy one to break). Be slow and methodical. Not a challenge once you study the owner's manual for door removal instructions.

I read all the repairs. Turned off power to oven. Was ready to clamp clips so the don't fall behind oven and Crap!! One clip popped off so easy, it went behind insulation. Had to pull oven out. Put wire through, connected everything. Turned power on and oven and broiler work great.

With some help from my wife.

Visited PartSelect.com and ordered the element. Talked to a really sweet lady who assisted me at the company by ordering the part. Received the part and my husband cut off the electricity to the stove, took off the old element, got the sockets and after pushing on the new element, and he screwed the screws back on, cut on the electricity and we cut the stove on and it was ready to go. VERY, VERY SIMPLE TO REPAIR.