GS395LEGB1 Whirlpool Range - Instructions

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

We removed with a screwdriver the two main screws that held the bottom of the oven in place and removed the bottom oven piece; then we removed the two nuts with a socket wrench that held the element in place. We then discovered that the element wire did not completely egress to the point of being able to disconnect from within the oven, so we removed the storage drawer below the oven and that provided access to disconnect the element wire and reconnect the new element wire and then reverse the steps to install the new element, which worked fine upon first use and continues to work fine.

took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.

Had to remove the bottom oven shelf and the broiler drawer. Disconnected the wiring pigtail theought the broiler opening and pulled the gas pipe from the baking oven. Reomved the two screws connecting the ignitor from the pipe. Connected the new ignitor and threaded the wiring pigtail back down the the opening in the baking oven. Connected the wiring harness up inside the broiler and put the drawer back in. Re-installed the bottom shelf in the baking oven and tested. Worked perfectly. Back to cooking. :-)

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

Oven is gas. Burners on top OK, broiler in oven OK. Removed oven bottom plate and heat deflector. Carborundum igniter would not glow. Ordered new igniter from Partselect.com. With new igniter in hand I unplugged the oven from house power, removed the bottom drawer for access to the igniter connector, and disconnected it. Removed the bad igniter and replaced with new igniter...easy! Plugged in oven to house power and tested new igniter by turning on oven. GOOD!! Reassemmbled oven interior. Wife again happy.

Was super easy even I could do it. Wish I would have done it 2 years ago when my husband broke it. Just used a Phillips screwdriver. Very easy!

I slid the range out about 8 inches from the wall, and having unplugged the range and looked at the diagram from the Parts Select site, I used a mirror and screwdriver to remove the screws holding the small rear cover. From there I removed the one screw holding the spark module and that way I was able to hold the old and new one side by side to move the wires. Reversed the process, easy peasy.

1st gen whirlpool Duet dryer sensor not working in automatic cycle.
After ordering the moisture sensor harness which is about 6-8 inches long, I removed the lower panel and it is right there. I disconnected the two wire connectors in the upper left and I need a small screwdriver to disconnect the two pin connector which was a bit of a pain but once replaced I no longer had to use the timed setting to dry clothes and this will save me electricity.

Called repair man and described the problem. He said I could do it myself. PartSelect had the part and a previous description on the PartSelect site told me how to do the repair. It was easy. Be careful when removing the igniter nuts. I used a very small amount of sewing machine oil so as not to strip the threads. works great.

The repair went well. Only took a few minutes. Oven is 21 years old and still working. I figured why throw away if still working. Thank you Select Parts for coming to my rescue. Will keep you in mind.

Loosen 2 screws and put new part in and tighten 2 screws. After putting in new sensor stove gave me another code had new part in 5 min and part select would not take my part back.

The video was very helpful and my wife did it..thanks….

This model does not have a removable bottom drawer making access a bit of a challenge.
1. Remove power to the range.
2. Remove the oven door and the kick panel below.
3. Remove the floor of the oven.
4. Remove the burner shield.
5. Become a contortionist, then stick your head and torso in the gas oven.
6. Look at the top in the back to see how the broiler igniter is mounted. Use this to select the proper size wrench. I suggest using little ignition wrenches. The oven igniter is mounted in the same manner.
7. Locate the oven igniter at the bottom, in the back, at the center. Remove the small screw taking care that you do NOT drop the wrench or the screw. This will be done by feel as the screw is only visible after you remove it.
8. Route the wire of the new igniter down, next to the old igniter wire.
9. Crawl under the oven (behind the kick panel you removed, and cut the wire.
11. While you are under there, strip the insulation back on the wires about 3/8 inch. Splice the new igniter wire to the oven using the new wire nut. Check that it is secure.
12. Back to the oven. If your back is still holding up, remove the old igniter. Install the new igniter and the old screw. Tighten securely, taking care to not strip the threads.
13. Remove all of your tools, your head, and your torso.
14. Plug the oven back in temporarily, turn the oven on and verify the igniter heats up.
15. Unplug the range again.
16. Reinstall the burner shield, the oven bottom, the door and the kick panel.
17. Make sure you have all of your tools, stand up, and since you are now a contortionist, pat yourself on the back!

Based on symptom, knew either switches or spark module. Checked continuity to each switch. Knew if only one faulty, entire harness must be replaced. Checked out good. Spark module isolated so replaced it.