RF398PXWN0 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Phillip from Pekin, IL
- Parts Used:
- 814103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
old stabilizer clip was broken
I removed surface burner and drip pan from stove. Then drilled out the remaining part of the old stabilizer clip. Once clip was removed I installed the new stabilizer clip with the screw and nut that came with the clip. Then I placed the drip pan back into position and installed the burner and locked it into the new clip.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline from Austin, TX
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Electric Stove Burner was working unreliably
pulled out the old burner, plugged in the new burner. Turned on the power and it heated up very quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Puyallup, WA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower oven element not working.
1. Turn off oven.
2. Switch off circuit braker to oven.
3. Remove two screws holding element.
4. Pull element out to expose connectors.
5. Disconnect connectors and remove element.
6. Reverse procedure for installation.
2. Switch off circuit braker to oven.
3. Remove two screws holding element.
4. Pull element out to expose connectors.
5. Disconnect connectors and remove element.
6. Reverse procedure for installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from PORT JEFF STA, NY
- Parts Used:
- WP660533
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The larger burners would stop working while in use.
The removal of the old burner and installation of the new burners was easy. Just lift the opposite side that rests on the rim and pull burner out. New burner then gets inserted and the opposite side goes right into rim. It took all of 30 seconds to replace both burners. I wish I had replaced these when they first started to go!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from WOODSTOCK, GA
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven didn't get over 300 deg. F.
Removed old element, replaced new element. Unfortunately, this didn't fix the problem. It was the temperature sensor. But now I have a new bake element, though!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from San Diego, CA
- Parts Used:
- W10858781
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace Disintegrated Chrome Trim Ring 8"
The repair was a trivial effort as all parts simply lift off the range top by hand. The impetus for replacement was pretty much looks driven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Decker from GREAT NECK, NY
- Parts Used:
- W10900107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Old infinity switch on electric rangetop did not work correctly
Lifted range top, disconnected and labled wires from old switch, removed old switch, replaced wires on new switch, installed new switch.
NOTE: Local appliance store informed me that the electric cooktop was too old and that a replacement switch was not available and wanted to sell me a new cooktop for $795!
I found the switch on PartSelect and repaired the cooktop. Total cost... UNDER THIRTY DOLLARS!!
NOTE: Local appliance store informed me that the electric cooktop was too old and that a replacement switch was not available and wanted to sell me a new cooktop for $795!
I found the switch on PartSelect and repaired the cooktop. Total cost... UNDER THIRTY DOLLARS!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James E from RIDGECREST, CA
- Parts Used:
- W10900107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
faulty switch
I found the received switch (PS12070192) a poor replacement for the original, or even the earlier replaced part (PS11744446, in 2016) I was going to replace since the press/return feature seemed slow to return.
The male spade lugs on the received switch are so positioned that engagement is only possible if the lug is bent out at a large angle. The lug set-back from the body edge, and the raised ribs on the sides still prevent full engagement of the connections.
I did install the new switch but found that was the only switch that didn’t give a signal light when turned on.
I have reinstalled the earlier unit.
Is part# PS 11744446 no longer available?
James E Weimholt. jmwm4031@verizon.net
The male spade lugs on the received switch are so positioned that engagement is only possible if the lug is bent out at a large angle. The lug set-back from the body edge, and the raised ribs on the sides still prevent full engagement of the connections.
I did install the new switch but found that was the only switch that didn’t give a signal light when turned on.
I have reinstalled the earlier unit.
Is part# PS 11744446 no longer available?
James E Weimholt. jmwm4031@verizon.net
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Fort Collins, CO
- Parts Used:
- WP8189867
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
light wont come on
Well, when you put the back cover on and screw it down make sure you have nothing touching the white wire leading to the oven light. I did and it blew the push switch when I threw the 220 breaker. Actually, the light was on when I came in the room, but when I pushed the switch on the front panel it sparked in the rear and popped the breaker. Then I saw the short and when I tested the switch it would not click. The install was fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from Spooner, WI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element went bad, will not work.
As soon the Bake Element has arive, I install it no more than 5 min... All I nedd was a Screw driver. It was so easy, Thank You PartSelet!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnson from Norwood, CO
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element Failed
I had previously partially removed the element and tested with multi-meter to determine that it was not working (open circuit). Repair procedure follows:
Turned off Power
Removed 2 retaining screws
Pulled element out part way
Removed 2 spade connectors supplying power
Replaced element w/new element
Reversed procedure
Tested Oven; worked fine.
Turned off Power
Removed 2 retaining screws
Pulled element out part way
Removed 2 spade connectors supplying power
Replaced element w/new element
Reversed procedure
Tested Oven; worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carolyn from ROGERSVILLE, TN
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element was broken
was very easy to install I only needed a phillips screwdriver to remove old part and install new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Wichita, KS
- Parts Used:
- WP3169203
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Cracked inner oven door glass
Did require removing almost every screw in the oven door. Labeled the screws as they were removed. Not difficult, just like solving a puzzle.
Was this instruction helpful to you?
Thank you for voting!
Intermittant Operation Of Surface Burner
I first tripped the power circuit breaker. Then I unplugged and removed the old element. Removing one screw allowed me to remove and replace the mounting clip. This did result in breaking off a small piece of plastic-like material from the electrical housing to which the clip was attached but did not hinder the replacement of the new clip. I inserted the new burner element. The surface burner is now working fine.
Was this instruction helpful to you?
Thank you for voting!