RF265LXTQ3 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- michael from mesa, AZ
- Parts Used:
- W11230488
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
chemical etching of black painted finish on drawer front panel
took out the drawer by removing two fillips head screws, four more screws removed the drawer front. Two plastic push pins and the front panel was off. Put the new panel on secured it with the pins, attached it back on the drawer front, put in the screws and slid the drawer back in the stove, put the two screws back in, done deal!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosalind from APOLLO, PA
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the oven temperature was not working right. I installed a new oven sensor. Works get now
Watch the video...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from HARMONY, MN
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
temp level uneven
after watching the video, installed the temp sensor. Super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from ONTARIO, NY
- Parts Used:
- WP8523178
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rust on oven door lower trim.
Do not remove the oven door. (Not necessary.)
Remove the lower storage drawer.
While laying on the floor, remove 5 screws on bottom edge of door, two on each end, one in the middle. Middle screw is slightly different than other 4.
Caution: When removing the lower trim, the front glass may slip down. Be prepared to catch it. The side trim pieces may also slip out.
It helps to have a second pair of hands here. If needed: Slide the front glass back into place. Slide the side trim pieces back into place.
Position new lower trim piece, align holes. Start with the center screw, then the end screws. Leave all screws "loose" until all 5 are threaded, then tighten.
NOT recommended to caulk trim to prevent future rust. The caulk will act like glue on the front glass.
Remove the lower storage drawer.
While laying on the floor, remove 5 screws on bottom edge of door, two on each end, one in the middle. Middle screw is slightly different than other 4.
Caution: When removing the lower trim, the front glass may slip down. Be prepared to catch it. The side trim pieces may also slip out.
It helps to have a second pair of hands here. If needed: Slide the front glass back into place. Slide the side trim pieces back into place.
Position new lower trim piece, align holes. Start with the center screw, then the end screws. Leave all screws "loose" until all 5 are threaded, then tighten.
NOT recommended to caulk trim to prevent future rust. The caulk will act like glue on the front glass.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ENID, OK
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven light kept burning out instantly
Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnie from PARKERSBURG, WV
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not heat up.
Unplugged the range. Opened the oven door and took out the shelves. Took the right screw out, but had trouble getting the left one out do to the age of the range. Unhooked the two wires and took the element out. Put the new one in and hooked up the two wires. Attached the two screws and checked to see that the element laid flat and then tighten screws. Closed the door and plugged the range back in and turned the oven on and it worked perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jenny from GREENFIELD, IN
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Removing an heating element that burnt into .
Unplugged oven , removed screws ,pulled wires out, removed old element , just hooked wires up , screws .make sure it sits level plugged in. Works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHILIP from NORTH PORT, FL
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
element not working properly
Remove 2 screws inside oven holding element . Remove screws holding back panel. Plug wires (2) into new element.Install back panel . Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from ASHLAND, PA
- Parts Used:
- WPW10308477, WP8053334
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Element had burned out, and the drawer glides were broken .
Replaced both .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wallace from Hanson, KY
- Parts Used:
- W10840298
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Shorted oven contoller and display module
Tool out 4 screws, unpluged the connectors, unscrewed two screws holding the module. Replugged the connectors, replaced screws. Done (don't forget to turn the power off)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alex from Athens, IL
- Parts Used:
- W10840298
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Stove top worked. When the oven turned on the timer would come on for the pre-heat but the oven never warmed up.
After I confirmed that the hearing elements weren't bad I started following wires and ended up at the control panel. After confirming with a multi meter that the elements weren't getting power I decided that the control panel was the problem. There are two screws that hold the panel in place. The connectors should plug right back into the new panel but mine didn't. After a slight modification i got it to work. The clips were different on the new panel so I just pulled the wires out I the connectors and plugged them into the appropriate slots on the panel. Oh, and the part arrived the next day and it was 3 days before Christmas. This is the second purchase I have made from them and I will continue to give them my business. A+!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from APACHE JCT, AZ
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Elementwas burnt into
Watched the video and did as shown
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandeep from EDINA, MN
- Parts Used:
- W10777162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
screw came off
very expensive to buy the part but just tighten the screw intot eh predefined place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Greensboro, NC
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Demon Possession
Our repair was extrodinarily easy. As my husband was taking out the old element and the oven was off, the element heated up and actually burned him. He readjusted it and it refused to heat again. We figured at that point that there must be a short, so we never even opened the box with the new element. A short time later we decided to use the top of the stove for soup and a small fire started in the oven. We turned off the braker at that point and ordered a new oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from JACKSON, WY
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
baking element non operational
removed two screws to faceplate at rear of oven. Disconntected contact wires, installed bake element reconnected contact wires, attached faceplate turned on oven holy hell it works just saved some money on service call thanks!!!
Was this instruction helpful to you?
Thank you for voting!