SF360BEEQ0 Whirlpool Range - Instructions

The brief comments on how to with the order was most helpful, no problems replacing frame. Quality is good I thought the price was very high for the parts, considering plastic and metal pieces, but then again compared to new stove reasonable. Remove pieces replace back in order removed.

I use the table knife to slide the side of the stove to open the top. then I traced one of the wire to where it was hooked up and remove it and replaced it. I did them one by one.

I still don't have it back together! The first time we ordered the part the gentleman sent me the trim for the left side which seemed to be fine but while replacing it the old part (right side) broke. Ok. so I called to order same part but for the right side. Well, the lady told me I could only order the oven door trim kit, which seems to be too large. I don't think she understood me. Why the 1st time ordering I could get the left side only now when ordering the right side she says we don't sell it that way. Very confused and still can't use my oven since Dec,19th!!

We removed with a screwdriver the two main screws that held the bottom of the oven in place and removed the bottom oven piece; then we removed the two nuts with a socket wrench that held the element in place. We then discovered that the element wire did not completely egress to the point of being able to disconnect from within the oven, so we removed the storage drawer below the oven and that provided access to disconnect the element wire and reconnect the new element wire and then reverse the steps to install the new element, which worked fine upon first use and continues to work fine.

Oven is gas. Burners on top OK, broiler in oven OK. Removed oven bottom plate and heat deflector. Carborundum igniter would not glow. Ordered new igniter from Partselect.com. With new igniter in hand I unplugged the oven from house power, removed the bottom drawer for access to the igniter connector, and disconnected it. Removed the bad igniter and replaced with new igniter...easy! Plugged in oven to house power and tested new igniter by turning on oven. GOOD!! Reassemmbled oven interior. Wife again happy.

took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.

Had to remove the bottom oven shelf and the broiler drawer. Disconnected the wiring pigtail theought the broiler opening and pulled the gas pipe from the baking oven. Reomved the two screws connecting the ignitor from the pipe. Connected the new ignitor and threaded the wiring pigtail back down the the opening in the baking oven. Connected the wiring harness up inside the broiler and put the drawer back in. Re-installed the bottom shelf in the baking oven and tested. Worked perfectly. Back to cooking. :-)

just replaced the broken glides with the new ones.

Undid one screw. Removed the broken slide. Replaced with new slide an fastened with the existing screw. Problem solved.

Called repair man and described the problem. He said I could do it myself. PartSelect had the part and a previous description on the PartSelect site told me how to do the repair. It was easy. Be careful when removing the igniter nuts. I used a very small amount of sewing machine oil so as not to strip the threads. works great.

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

Used a phillips head screwdriver to remove the single screw holding the part in place and put the new one on. Finding the part on this site was a breeze and it arrived quickly. A first rate experience all around.

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

I used a phillips screwdriver and replaced the part with one screw.Very easy and replaced my lower drawer under my oven,it tool about three to five minutes at the most and my drawer works fine now.Thanks for the instruction video on line, it really helped.

Only one screwdriver needed for this simple repair. Unfortunately for me it did not repair my oven and a new code on the oven indicated a bigger problem with computer board.
Part Select was great to work with and accepted a return and promptly refunded me for the part.
Thank you!