GS563LXSQ1 Whirlpool Range - Instructions

all I did was replace the igniter and that fixed my problem simple to do.

I remove bottom trim which is held on by 3 screws and try to install new bottom trim, did not work well. I then remove yop handle assem. Then the door glass which you need to clean after. Then install the new bottom trim then insert the glass into the new bottom strip using masking tape to hold the glass and side strips in place prior to installing the the top handle piece which is held on by two screws. Not a hard job to do.

Removed door per instructions in manual. Removed racks and storage drawer per manual. Removed two phillips head screws holding bottom pan and removed pan. Removed two phillips head screws holding igniter tube (#12) and withdrew tube from the cavity. Removed two phillips head screws holding igniter and bracket to the tube. Unplugged elcetrical connection to igniter and installed new igniter in reverse order. Too bad the igniter wasn't the problem.

Replaced bake igniter only as recommended by others, no need to buy the whole unit. The bottom screw is difficult to access, use a 1/4 inch socket set with 8 mm socket. Advice to remove bottom storage drawer to make sure wire is connected to the igniter. So far it works fine.

removing the screws holding the burner together was impossible. they snapped off and I had to drill them out. that took the most time. after that it was 100% easy hookup. clean up of the burner was done with a wire brush. good quality products. thanks.

We took the door off and took it and the side panels to the local dealer and he put them on for us - for anyone needing to replace the side panels on the over, be aware they slide under the glass front -not over it like we tried to do. We thought, though, that we were going to have a buy a new stove but for a little over $70. 00 We got the parts, had them installed and saved over $800 on a new stove - well worth the effort.

I had to use a dremel to grind the heads off the rusted in screws that hold the burners to the stove top then drill out the screws and use larger sheet metal screws to reassemble. Don't lift the stove top much with the burners attached or you'll bend the gas lines. Two screws inside the top oven hold the top down. Without the rusted screws it would be an easy job.

Removed back of stove, 8 screws, removed original latch assembly and installed new assembly. One thing that can cause you difficulty is that the rod that connects the assembly to the front latch on the door can disconnect and has to be reconnected.[Problem]

oven would not light but broiler and range top would. removed oven racks. removed 2 finger tight screws on oven pan floor and pulled up oven floor. also removed storage drawer under oven- also 2 screws. now your oven should look like the inside of your gas grill. removed 2 more screws on burner plate and removed plate. unplugged igniter and 2 screws holding igniter. replaced igniter and put together in reverse order. oven now works perfectly

Take off the back panel of stove and unplugged timer motor and switch on door latch assembly,removed two screws that hold assembly and slide rod off. I put 110 volt plug to timer motor and it did not move, that is how I diagnosed problem. Ordered new assembly (cannot buy just timer motor)put new door latch assembly on and worked fine. Of course unplug stove before you start !

Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.

Open oven door and remove racks. Remove 2 screws at back of oven floor and remove bottom plate. Unscrew screws that hold flame defuser. Remove defuser. Remove screws that hold bake igniter and flame tube. Unplug wire to bake igniter. Remove screws to bake igniter. Replace old igniter with new igniter. Replace screws and wire to igniter. Replace flame defuser and put screws back. Put bottom plate back into oven. Replace 2 screws at back. Replace racks. close door and test by setting thermostat to some temperature and verify that oven works.

So, after several years of it bothering me, I decided to replace the oven panel. I ordered it one day and it arrived the very next day. It was an easy job to replace. Just remove two screws in back and replace the panel. While I was at it I also replaced the racks. Now I have a brand new oven,thanks to PartsSelect!

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Pulled shelves out removed bottom plate of oven remove heat shield cover removed screws had to remove bottom drawer disconnect wire from bottom of igniter and remove from top side . Replaced by reversing steps.