WERE3000SB1 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from SHELBYVILLE, TN
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
8” burner on low would run away. Burn solid red.
I installed the new switch. No difference. I switched elements with the other 8”. Same thing. I called Part Select and their rep said he doubted the new switch was defective but if it was they would replace it. But first how about trading the new switch with the other 8” switch that is working. I did that and the new switch worked fine on that burner but the old switch that worked before allowed the bad burner to go to red hot. Now I’m at a loss. All I see is a new stove. I don’t know what to do next and am open to any and all suggestions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from ASHLAND, PA
- Parts Used:
- WPW10308477, WP8053334
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Element had burned out, and the drawer glides were broken .
Replaced both .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Birmingham, AL
- Parts Used:
- WP660532
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
burned out stove eye, 6"
remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myron from Punta Gorda, FL
- Parts Used:
- WPW10118454
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Glass Door Broken
Removed 3 screws holding the glass door bracket.
Placed glass into door holders, had another person hold glass while I replaced the removable bracket screws.
Placed glass into door holders, had another person hold glass while I replaced the removable bracket screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from BRIDGEBORO, GA
- Parts Used:
- WPW10181986
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven temperature was 50 degrees off
Unplugged stove.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Duarte, CA
- Parts Used:
- W10355051
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cleaner
just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudia from Milwaukee, WI
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My drip bowls were scorched and discolored and difficult to clean
I removed each surface coil burner from its receptacle; removed the old drip bowls and replaced with the new ones; my stove looks good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alene from INDIANAPOLIS, IN
- Parts Used:
- WP660532
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burners needed replacing
Pulled out the old burners and put in the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from LEBANON, VA
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Light would not light
Pop old one out and new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Council Bluffrs, IA
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Replace burner drip pan
Removed electric coil replaced pan and reinstalled coil. Part fit just right and no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marlene from Charleston, SC
- Parts Used:
- WPW10259865
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
surface burner heating element broken
took out old element, replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dann from Glendale, AZ
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
reflecter/drip pans wrong size
Ordered acording to range model & such. Had ben unsucksessful gettin the right size thru the years & finally got the correct ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Hamilton, OH
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Eroding burner drip bowls
Removed old drip bowls and installed new, which, thanks to your efficiency, were a perfect replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leona R from Louisville, KY
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
slides on lower drawer were broken
I used a phillips screwdriver and replaced the part with one screw.Very easy and replaced my lower drawer under my oven,it tool about three to five minutes at the most and my drawer works fine now.Thanks for the instruction video on line, it really helped.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!