FEP330VL1 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- judy from coarsegold, CA
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner fell apart
Just plugged it in and away I went.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PATRICIA*NAYLOR from NEW PRT RCHY, FL
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Generic Drip Bowls Made The Burners Tilt.
Pulled out the generics and popped in the correct bowls for my whirlpool. Done in less than 10 minutes and perfecto,. . . Level burners :-) thanks we'll be back when we need you again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Spring HIll, FL
- Parts Used:
- W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The burner didn't work because it had the wrong drip bowl
Replaced the drip bowls, very simple. Excellent delivery time, ordered them Saturday, delivered Tues morning.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Villa Ridge, MO
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
one burner that would not heat and others that would not out out much heat
I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove the screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christina from West Des Moines, IA
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
range installer broke a screw off & busted the plastic piece
Had to screw off old terminal block & screw on new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vincent from Martinsville, VA
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
electric surface unit not working
After turning off circuit breaker to the stove, I removed all surface units , removed the 4 screws holding the top and lifted up. The plug in was burned out (the wire was burned). Look at the old plug-in so as to be able to match the new one and insert the pre- crimped end of wires into the block and the block into the metal holder that matches your old one. (The kit comes with 2 different metal holders)After this, cut out the old wires and wire nut the new wires with the stove wires. Put shrink wrap protector on the wire nuts and heat to shrink it tight.attach the block to the stove top and wa la its done. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Union Mills, NC
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner would not heat up the connection was bad
loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Graham from Bridgeville, CA
- Parts Used:
- W10900107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic post for knob broke off
I broke the correct post from the new cluster of post selections and stuck it on. I had the kit for a couple of weeks before I realized that this was not an electrical problem. It would have been good of you to send only the new plastic post. That kit was intimidating for a 73 year old woman who lives in the country and does most of her own plumbing and other household repairs. The repair took less that one minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Boca Raton, FL
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Two drip Bowls needed to be replaced
No tools needed. And it's always great to be able to replace parts on my VERY old counter-top range. It still works very well, and now it also looks great. Delivery was amazingly fast, too! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Addison, TX
- Parts Used:
- W10900107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Original burner switch fell apart
Replacement was simple. Old switch was easily removed. Once I swapped the wires from old to new we were in business. One thing I would do differently than the included directions called for. I wish I had waited until I had installed the new switch to set the shaft length. I snapped off one too many sections of the shaft after measuring the original shaft as recommended. If I had installed the replacement switch and then set the shaft length it would have been more accurate. Everything still works but one knob is now slightly lower than the other three.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Memphis, TN
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip Bowl beyond cleaning
Removed old bowl and dropped in new one!!It looks great - the cooktop is probably 30 years old.Your serviceperson was courteous friendly and very rapid.This actually is the second replacement but I was pleasantly surprised that the part was available. Thanks!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from Price, UT
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
stove burner no longer would heat up burner element
I removed the burner element, then the drip pan. I took off the old block. Then I had to strip the old wires. Then I put on the heat sleeve, then attached the new wires to the old wires with nuts. Put heat sleeve over this and heated with lighter. Then put everything back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Montgomery, AL
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Top element not heating
Ordered wrong part at first caused me to blow out two elements. With the help of PartSelect I was able to get the right surface block terminal and replaced both of them, then found out I had a bad switch, they got the switch within 2 days I had my stove working good again. Thanks to PartSelect. Also watched the video which was very helpful ML
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gene from kent, WA
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner not working
burner was shorting out replaced part works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kyle from Schwenksville, PA
- Parts Used:
- W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rusted drip bowl
remove burner by hand and remove old drip bowl replace with new bowl inspect burner for ware and insert back into slot.
Was this instruction helpful to you?
Thank you for voting!