Models > RF362BBDQ0 > Instructions

RF362BBDQ0 Whirlpool Range - Instructions

Jump to:

All Instructions for the RF362BBDQ0
106 - 120 of 486
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Heriberto from AUSTIN, TX
Parts Used:
WP8053344
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
THE OVEN WAS NOT HEATING TO DESIRED TEMPERATURE
DISCONNECTED POWER AND GAS TO THE RANGE. REMOVED 6 SCREWS FROM REAR OF THE RANGE. REMOVED THE 2 SCREWS HOLDING THE TEMPERATURE SENSOR IN PLACE. DISCONNECTED THE LEAD FOR THE SENSOR. INSTALLED NEW SENSOR IN REVERSE ORDER. OVEN WORKING PROPERLY NOW.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lowell from Aberdeen, MD
Parts Used:
WP308180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Turn on the oven to heat up for cooking, Heard a ark sound, open the oven door and there was a fire on the element. Turn off the oven.
I had to pull the stove out from the wall and discounted the power source from the wall. Than I used the a phillips screwdriver take out the heat element. There was now problem fixing the stove. Lowell Moxley
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
richard from burnthills, NY
Parts Used:
WP308180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
burnt out bake element
unscrewed two screws put in new element replaced two screws done, recieved the element within days of order,it was the right part,couldn't have been happier with the service from parts select thank you.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Longview, TX
Parts Used:
WP308180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Element broke into several pieces
Was able to use a philips screwdriver and remove 2 screws. I then clean the bottom of the oven. The installation was even easier. Took less than 5 minutes. Saved over $60.00 in labor cost
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
denise from swartz creek, MI
Parts Used:
WP308180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Bake Element quit working
Removed the 2 screws that hold the element in place. Pulled the element forward about 3 inches and disconnected the two wires. Plugged the wire clips onto the new element and pushed the element back into place. Put the 2 screws back into place. This was a very easy repair.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOSEPH from COON RAPIDS, MN
Parts Used:
W11594027
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Worn/Bulb Socket
It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
DAVID from PETALUMA, CA
Parts Used:
WP660533
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Oven Wouldn't Heat
Of course, power off first, then I removed the old one and inserted the new one, make sure everything in right place, then turn on power, simple as 1-2-3.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Don from Rutland, VT
Parts Used:
WP308180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven wouldn't heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires fom the old element .. connected them to the new element ... put the screws back ...and tested. problem solved
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Margaret from PUTNAM VALLEY, NY
Parts Used:
WP8053344
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven was overheating and locking the door. Codes indicated the temperature sensor could be the issue.
Only one screwdriver needed for this simple repair. Unfortunately for me it did not repair my oven and a new code on the oven indicated a bigger problem with computer board.
Part Select was great to work with and accepted a return and promptly refunded me for the part.
Thank you!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from MIDDLE RIVER, MD
Parts Used:
WP308180
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Bake Element burned out
Turn off the oven circuit breaker. Remove 2 screws that hold the element in place. Carefully pull element out, about 3 inches and remove 2 attached wires by holding the element and pulling the wire clips off of the old element. Slide wire clips onto the new element and put the screws back in.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from DANBURY, CT
Parts Used:
W10196405RW
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Old drip pans made to heating element un ever
Replaced drip pans and now everything is level.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Phillip from YONCALLA, OR
Parts Used:
WP308180
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Oven Heating element had a melt down and small explosion
Remove racks, extract two phillips head screws, pull out element, unattached wires, install new element, reverse procedure to complete installation. (Note: With the racks and element out, great time to clean oven.)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary from CHARLESTOWN, IN
Parts Used:
WP660533
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Element did not heat
Pulled out element, plugged in new element. About 5 seconds.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edward from TAYLORS, SC
Parts Used:
WP3149400
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
surface element out
Unplug from outlet and top remove back section of range and unplug wiring from switch, remove knob and unscrew two screws and remove old switch. Install new switch reinstall screws and plug switch plugs into new switch (will only go on the correct way). reattach back and plug into outlet. All done and surface element works perfectly.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brian from YORK HAVEN, PA
Parts Used:
WP3149400
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Right front burner would only stay on high
Turned off breaker, pulled stove from wall, took off knob, unscrewed and pull off backing from stove, unscrewed heat control part, unplugged wires, plugged into new part, installed part, replaced stove backing, replaced knob, pushed stove back in place and turned on breaker. It worked fine.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the RF362BBDQ0
106 - 120 of 486