GGE388LXS03 Whirlpool Range - Instructions

Had an electrician to do the job for me.

Turn off 220 voltage, unplug and remove clips. replace it with new part. Check part before replacing the top of range, if it works, the electricity can be turned back on. Repair done.

It turns out that the 6" and 8" burners we actually broken and the infinite switch for the 8" burner was not working properly. These we very simple replacements. You just need to note the numbers on the original burners to make sure that you use the same numbers on the bottom of the burners so that they install in the same slots. The wires on the infinite switch match and this takes less than 5 minutes to remove the back of the stove top and the front switch handle. Simple replace the infinite switch and the burners and whoowhooo ,,.... the fix is done.

Changing out the switch was easy. Paid attention to wire connections to avoid mixup. Removal and installation of the switch was easy. It's the back panels that gave me the most challenge. Used screwdrivers and needle nose pliers to do repair. Having a second set of hands for the two part back panel reinstall was most helpful, but can be accomplished by 1 person.
Burner works great. This is a easy DIY fix.

Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair

Pop old one out and new one in

the part conections were different from the original.so the first i did was to call parts direct to see if someone will help.NOBODY WAS ABLE TO HELP. so i had to use a lot of common sense to install this my self.

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

ordered new broiler pan

Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white too.

Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.

replaced light socket but did not repair problem. must have burned the motherboard.


pleased with service from your company.

Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.