WFE320M0AB0 Whirlpool Range - Instructions

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

Slide range out,unplug range,remove rear cover to unplug element wires, open door remove screws inside oven remove element

My oven was assembled at the factory with half a hinge in left side ( no giant spring assembly) and in 15 months the right side hinge twisted and collapsed from bearing all the weight. First I thought I was only dealing with one bad hinge, and took the screws out of one side of door only and replaced hinge and was done in five minutes. Watched YouTube videos which were great and did the repair . Then I noticed the other hinge had no tension on it and did a complete disassembly of door and compared hinges and discovered the other shoddy assembly. I recommend you try to replace one hinge at a time. Take out screws on one side and finagle hinge into place. I did not do this and it took a long time. Rated repair difficulty due to several parts of oven door need to be aligned correctly to get the screws back in. Getting one side aligned caused the other side to become mis-aligned. Not rocket science but requires a lot of patience as you will redo it many times. I screwed the new hinges/steel channels they sit in into the inner door to help reduce the number of moving parts. Then aligned and secured door parts. I cut a 6” piece of straight wire from a coat hanger and stuck it through the screw holes to line them up. Worked very well, and after door was screwed together then I finally screwed the hinges to the outer door.

Shut down breaker; remove stove back cover plate (8 screws); remove the control knob; remove knob screws (2); simply remove one wire at a time and replace the coresponding wire to the new control unit; remove the snap ring on the knob bar and snap off to fit the proper length; place the control unit in position and reinstall the 2 screws; reinstall the back panel; position stove and turn throw the stove breaker on; test the burner control.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

It was simple. Unscrewed to screws at the back of the oven. Slipped off the wire connectors then attached the wire connectors to the new part, put the screws back in and we were back in business.

Remove back panel 10 screws. Disconnect plug in fixture from switch. Front of range remove knob (it just pulls out) remove 2 screws, remove switch. To install reverse procedure.

repair was very easy 20 mins and it was done

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

Took off top and pulled out old element and plugged in the new one

Ordered a new switch and replaced the old one with it.

My husband pulled the oven out and unscrewed the screws(in the back) the heating element came right out. He did everything on his own. The only thing he needed a little help with was for me to keep the heating coil flush to the back wall of the oven, while he screwed the new one in. It was a very quick job. The longest part was pulling the oven out to get behind it and sliding it back in.

Wire connection was damaged, replaced end piece

My wife did it! I got home one night and my wife had done it! That's how easy it was! Trust me, he is no handyman (woman) but she did it by herself. The part came fast, the price was better than any one else's

Shut off breaker. Remove a total of 3 screws attach wires, replace screws, turn breaker on. Done!