YWFE366LVQ0 Whirlpool Range - Instructions

I watched the video you provide and it answered all my questions. You estimate repair at 10 minutes. My wife said I waz done in under 10 minutes Watch the video, it explained every step and all the little tricks to the snap connections.

Removed drawer, after removing the 50# of junk in the drawer, Used screw driver to remove screw that holds glide to drawer and then place new part into place put screw into hole and tightened screw. Replaced drawer and told wife not to put 50# of junk back into the drawer.

Open door 1/4 an slide the little latches on each hinge toward you. This will lock them in place. Close the door a little and lift it up. The door will slide out. Lay it face down on a table and undo all the screws. Do not remove the glass, frame etc. Slide old hinge out and new one in being careful not to slide the glass and frame out of alignment. It is a pain to get it all back together if you take every part out. Just do the hinges. Screw it back together. Reverse the door removal process by lowering the hinges into the oven receiver from a 75% closed position. Once in place, open the oven about halfway and slide the locks forward. This will allow the door to close completely. Note: Three hinges came with my set. Not sure what the third odd one is for.

Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.

This was a very smooth repair. In total it took about 5 minutes. The pot drawer below the oven wasn't gliding like it once did. After I replaced the glides it works like new. Please note, if you are going to replace one side go the next step and replace both to provide balance to the drawer.

I removed the bottom drawer,unplugged the Range and pulled it out to expose the rear cover panel. Using a nut driver (a screw driver can be used), I removed the rear panel to expose the Thermal fuse located almost dead center in the back of the Range. Unplug the two wires and loosen the screw holding it in position. Replace the thermal fuse, plug the two wires into the new part and replace the rear cover panel. Return the Range to its original position and plug it in. The job is done in less than 30 minutes.

First Things first, unplug unit, remove rear cover with Phillips head screwdriver, disconnect, wires from broiler element which is the top, one, open oven, unscrew top screws first, then two at the back, wiggle out element, then reverse Steps , test repair before putting cover back on. Then ta-da, you saved yourself a $300. Service call to the appliance repair guy.

We cheated; a local appliance repair company was called & the tech guy repaired it in 10 - 20 minutes. Couldn't be happier.

Watched video & did just guy in video did. Very easy job & the burner works like new.

After doing a YouTube search. I successfully completed the repair by easily diagnosing the issue with the element.
I watched a video about 5 most common problems with whirlpool broiler elements.
The first being to inspect the element for damage. I found a small section that appeared to be rough and had a raised bump.
I decided to order a new element because the oven is older and it wouldn’t hurt to install a new one even if this wasn’t the issue.
Once the part arrived, which it did quickly, I followed the video instructions. It was easy and straight forward. I completed the task in under thirty minutes. It was very simple and I now have a functional broiler element.

By hand screwdriver

Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place

Pleaae prepopulate the manufacturer and part i purchased. I fix a lot of appliances so cannot expend the effort to decipher this.

Be well.

removed 3 screws holding the strip and replaced with new strip

I replaced the infinity switch exactly as shown in the YouTube video provided by Part Select. Watch the video all the way through once before installing, and then have it open while you perform the repair. Watch a step, then pause it while you perform the step. Play the video to show you the next step, then pause while you complete the next step. It seems impossible to not perform the repair properly by doing it this way!