WDE150LVS01 Whirlpool Range - Instructions

Pull range out 6 inches. Open door to 45 degrees and pull up to remove door. Remove both side plates, two screws each side. Remove both hinges by loosening two small bolts on the front of range that connect to the hinges. Place new hinges in place. Bolt hinges using bolts you removed, replace side panels. Slide door on hinges and push back range.

Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.

Turn off breaker in electric panel fore stove. Put screw driver into slots in front of glass top surface. Pry top up carefully until top pops up.Remove burner dial, remove two philips head screws holding switch. Lift top carefully and prop up.With new switch close remove wires from old switch one at a time and place on new switch. Place new switch back in place, securing with philips screws. Remove prop and carefully press top down until it snappes into place.Replace dial, turn breaker back on and try burner.

I didn't. Don't know how to get to light bulb to change it for this specific model

Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!

Repair was very simple. Took the door apart in layers, replaced the glass and put everything else back. it took longer to clean the stove than it did to actually take it apart and put it back together. guess i didnt need to be that much of a clean freak!

I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.

I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.

First be sure to unplug stove or turn off from breaker switch. I Removed racks from oven . Using screwdriver I loosened the back plate in the oven that held the wires connected to heating element , being careful not to let wires fall through holes . Gently pull element tip apart from wire. Snap end of new element to wires, screw plates back to tighten
Turn oven on and check to assure heating properly. Very simple

Shut off power at breaker box , pull stove away from wall , remove Phillips screws from back of range pull knob off of switch . Look to see how switch is oriented remove 2 screws that hold switch in . Remove one set of wires at a time and place on new switch in same location . Put back together in reverse order .

Took the old levelling leg out and screw the new one in.

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.

Shut off breaker, assure zero energy. Using phillips screwdriver remove old element, unplug wires from element. Reconnect wires to new element, secure screws. Assure all tools removed and people are clear before re-energizing power to range. I was not happy with the packaging, the new element came in a box with no protective packing material!

No instructions with part, so I had to look up on internet. This took more time than installing it. Think basic instructions should come with the expensive part.

1. Open oven door to first detent, then pull it up off the hinges.
2. Pull oven out from counter 10-12 inches.
3. Hinges are accessible from the outside of the oven.
4. Remove 2 screws on each hinge and remove old hinges.
5. Put new hinges in place and try to insert mounting screws.
6. Wonder why screws won't start in threads.
7. Examine new hinges and notice they are not threaded for the screws.
8. Screws are not self-tapping, so go to basement and get tap & die set.
9. Use 10-24 tap to make threads in new hinges.
10. Put new hinges in place and insert mounting screws. Tighten.
11. Pull hinges to first detent and put oven door on hinges.
12. Push oven back into place in counter.