WFG111SVQ0 Whirlpool Range - Instructions

I shut off the gas and removed the back plate and disconnected the wires. Then I unscrewed two screws from the igniter and replaced the old with the new. Then I snapped the wires together and put the back plate back on. The oven works great!

We just put the new burner cap on the stove, and my husband just slipped the new handle on the stove.

Removed a cover plate on the back of the stove. Unplugged the old igniter. Pulled the bottom drawer out. Reached in under the stove and undid the 2 screws holding the igniter in place. Screwed the new igniter in and put everything back together. The only tricky bit was reaching the igniter through the bottom drawer opening.

Shut off gas and unplugged electrical cord. Removed grates; oven floor and flame spreader and then unbolted old igniter with nut driver. Removed shield in rear of over with Phillips screwdriver and unplugged igniter from power socket. Removed old igniter and replaced with new. Bolted new igniter into place with nut driver and plug into rear socket. Turned on gas and plugged in electric to test igniter; saw white glow and flame on in a minute. Replaced rear shield, flame spreader, oven floor and grates. DONE!

Our oven wouldn't light as the ignitor wasn't getting hot enough. I ordered the part from your company and got it in just a few days. A quarter inch wrench and one plug, done!

I pulled the stove out from the wall & took the back lower right cover off. Unplugged the power cord & disconnected the igniter from the power. Took shelves & bottom cover (took two screws out)from oven. Used nutdriver to remove old igniter, then pulled the connector through into the oven, discard. Put new igniter in place with nutdriver.Push connecting cord through to back of stove.Replace bottom cover & shelves. Plug cords together & plug cord back in to outlet.Turn stove on & igniter works!!! Push stove back into place & bake a cake! :)

most difficult part was having to pull the stove out to access the Igniter wire connector. unplugged connector, removed 2 Igniter mounting screws, installed new Igniter and connected plug. very easy project. less than 30 minutes total thanks to website for perfect diagnosis of problem

Removed bottom plate by pulling up from the back (had some resitance), Two machine screws holding cover over igniter, used 3/8" socket to remove. Pulled oven from wall to disconnect igniter @ coupler, unscrew one more machine screw, fed replacement igniter into slot and coupled, attached single screw to pipe, put cover w/ 2 machine screws on top, install bottom plate. Had to use butter knife to get bottom plate to fit into the front cabinet area of stove. Done & working fine.

it was abit difficult to remove the rusted hinge because of rust, but after getting it out and securing the new one, I realize I had an even bigger problem. The new hinge was closed and the spring was very tight.After a closer look at the other side of the oven door where the hinge was intact, I saw a hole in the hinge when it was opened. So I opened the new hinge by pulling it open and exposing the hole, put a pin in the hole.I then put the hinge in position and put in the screws.But now the door wouldn't go into position. I then had to put pins on both hinges and slide them in at the same time,locking them into place.This was the first time i ever took out an oven door or attempted any stove repair.

Opened lower door of stove located ignitor removed 2 small screws that secure part, took guard off back of stove unplugged wire connector removed part plugged new ignitor in re-installed guard, re-installed 2 screws that secure ignitor. Turned stove on oven lit problem solved. This is the 3rd time i have used instant repairman on parts select to fix 3 different applicances and have saved hundreds of dollars fixing it myself with the help of parts select.

It only took my husbend 6min to put in the new oven igniter. But it did not work, so I call your center and the rep there talk my husbend and told him how to unluck the key bord, and that worked. Thank you for all the help.

ordered the part and in less then 24 hours from ordering the part it was shipped and delivered and my husband and I put the part in took us no time at all very easy to do... 2 years ago i had this same problem and called a guy in the area cost me $200. I had dinner in the oven by 5 that night!!!!

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

I removed the oven racks, removed the oven floor and the oven burner cover, pulled the range out and removed the small panel on the back which covers the igniter connector. I disconnected the old igniter, removed the two screws holding the igniter in place and removed the old igniter from the oven. Then screwed on the new igniter, fed the wire through to the back and connected the new igniter. Turned on the oven and voila' we have ingnition! The oven is working again but I'm getting the "F2" routine sometimes. It doesn't do it every time but when it does I unplug and replug and then it works. I'm a 67 year old female and I considered it very easy so pretty much anyone should be able to do this repair.