Models > RF111PXSQ3 > Instructions

RF111PXSQ3 Whirlpool Range - Instructions

Jump to:

All Instructions for the RF111PXSQ3
106 - 120 of 251
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
PHILIP from NORTH PORT, FL
Parts Used:
W10856603
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
element not working properly
Remove 2 screws inside oven holding element . Remove screws holding back panel. Plug wires (2) into new element.Install back panel . Done.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Johnie from PARKERSBURG, WV
Parts Used:
WPW10308477
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Oven would not heat up.
Unplugged the range. Opened the oven door and took out the shelves. Took the right screw out, but had trouble getting the left one out do to the age of the range. Unhooked the two wires and took the element out. Put the new one in and hooked up the two wires. Attached the two screws and checked to see that the element laid flat and then tighten screws. Closed the door and plugged the range back in and turned the oven on and it worked perfect.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeff from Manhattan, KS
Parts Used:
WP8053334
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
broken rear drawer glides
just replaced the broken glides with the new ones.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Diane from Gillett, WI
Parts Used:
814399
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Oven heating coil snapped and would no longer heat.
It was so easy to change this out. Unplugged the stove and removed a couple of screws on mounting plate and pulled out the old heating element. Plugged in the new one and replaced the screws. Problem solved!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from PRESCOTT VLY, AZ
Parts Used:
WP9762477
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Removed handle on oven door to remove front glass to clean when it slipped out of my hands.
To replace, the front glass slides into two holders on the bottom and three groves in the handle, then two screws to attach handle in place on the door.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOSEPH from COON RAPIDS, MN
Parts Used:
W11594027
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Worn/Bulb Socket
It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
karen from Thornton, CO
Parts Used:
WP8053334
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Broken drawer glide
Used a phillips head screwdriver to remove the single screw holding the part in place and put the new one on. Finding the part on this site was a breeze and it arrived quickly. A first rate experience all around.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Leona R from Louisville, KY
Parts Used:
WP8053334
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
slides on lower drawer were broken
I used a phillips screwdriver and replaced the part with one screw.Very easy and replaced my lower drawer under my oven,it tool about three to five minutes at the most and my drawer works fine now.Thanks for the instruction video on line, it really helped.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
GARY from JACKSON, WY
Parts Used:
WPW10308477
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
baking element non operational
removed two screws to faceplate at rear of oven. Disconntected contact wires, installed bake element reconnected contact wires, attached faceplate turned on oven holy hell it works just saved some money on service call thanks!!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Claudia from Milwaukee, WI
Parts Used:
W10196406RW, W10196405RW
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
My drip bowls were scorched and discolored and difficult to clean
I removed each surface coil burner from its receptacle; removed the old drip bowls and replaced with the new ones; my stove looks good as new.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary from Duarte, CA
Parts Used:
W10355051
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
cleaner
just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Samuel from RICHMOND, MI
Parts Used:
WPW10345407, WP9761346, W10196406RW, W10196405RW
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Replacement of one small and one large electric element burner and drip bowl.
Replaced old parts with new. Elements and drip pans fit perfect and snug. No issues. Would purchase again if needed. Thanks!
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gregory from BRIDGEBORO, GA
Parts Used:
WPW10181986
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Oven temperature was 50 degrees off
Unplugged stove.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Frank from LEBANON, VA
Parts Used:
W11594027
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
Light would not light
Pop old one out and new one in
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ivanka from Atlantra, GA
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
3 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the RF111PXSQ3
106 - 120 of 251