GY397LXUT03 Whirlpool Range - Instructions

took off nobs, pulled stove out 2 inches to access front side screws,( has 1 philip screw on each side end and four nut screws under panel) pulled panel out and flipped forward and down, all switches exposed and took apart broken switch and installed new switch(PAY ATTENTION TO WIRING PATTERN), reverse order for install back. bingo!

Had this range for 6 years. My daughter turned on the burner and it went "pop". She was very upset. I found the best price at PartSelect, and ordered the same day.

the first burner arrived broken in the box. We contacted PartSelect, and they immediately sent another and rushed shipping. It arrived in excellent condition.

To replace the unit: First, I turned off the circuit breaker for the range. Then I removed the two Philips screws that held the cooktop down. Next I removed the nut screws holding the burner to the cooktop.

Then I placed the new burner next to the old one, and one by one swapped the wires (this way I was sure I had the right wire on the right connector). One of the wire connectors broke when removing it from the old burner. PartSelect had provided 4 repacement connector pieces (oddly, all of which were too small for the burner element). So I located a replacement connector at a local hardware store. Stripped the end of the wire and used pliers to fasten the new connector.

After all connectors were secured to the new burner, I screwed the burner to the cooktop, then closed the cooktop and secured it with the two screws.

Turned on the circuit breaker, and it works like new! Saved over $100 by doing it myself!

Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!

1. Lift the Oven Door off of the 2 stove hinge mechanisms.
2. Remove the screws holding the bottom Glass Support Bracket.
3. Slide the Support Bracket out from under the oven door side bracket tangs and off the cosmetic front glass.
4. Slide the glass out of the top bracket and thoroughly clean both sides of the glass with glass cleaner and wipe with paper towels.
5. Slide the new Glass Support Bracket onto the bottom of the glass, slide the glass back into the oven door top bracket, and slide the new bracket under the oven door side bracket tangs.
6. Reinstall the screws, and then slide the oven door back onto the 2 hinge mechanisms on the stove.

Repair was very simple. Took the door apart in layers, replaced the glass and put everything else back. it took longer to clean the stove than it did to actually take it apart and put it back together. guess i didnt need to be that much of a clean freak!

Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.

I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.

I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.

I didn't. Don't know how to get to light bulb to change it for this specific model

First be sure to unplug stove or turn off from breaker switch. I Removed racks from oven . Using screwdriver I loosened the back plate in the oven that held the wires connected to heating element , being careful not to let wires fall through holes . Gently pull element tip apart from wire. Snap end of new element to wires, screw plates back to tighten
Turn oven on and check to assure heating properly. Very simple

The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.

Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.

My grandson, age 15 did the replacement. Now, how easy is that!

Important to unplug the appliance first. There were two screws which were at the top opening of the oven. They were a bit obscure, but with a bit a searching, I was able to find them. After removing those two screws, the entire top lifted up. There were four screws from the bottom of that assembly which were easy to find, and once removed, the top lifted of easily. I found it easier to remove the two power lines with two easy disconnects, this made it easier to work on the assembly. The element itself was held down by two simple clamps which required no tools. There were four easy to remove wires, and the element came right off. Simply reversing the process put it right back together, plug it in, and back to cooking again.

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.