ISE630VS11 Whirlpool Range - Instructions

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

1 Turn the circuit breaker that feds power to the range/stove off
2 Opened the oven door and found two screws that hold the top part of the range. I removed the screws and disconnected the green cable (ground) so I could have access to the Element-surt
3 Disconnected the four wires that connects the Element and removed the braket that holds it.
4 Replaced the new element, connected the wires and attached the braket.
5 Connected the ground (green cable) and place the top back on place (screwed the top from inside the oven).
6 turned the power on

Removed the old sensor by removing two screws and pulling the wire out through the hole. Disconnected the connector and discarded the old sensor.
Selected the correct connector of the 3 provided, plugged the new sensor in and threaded the wire back into the hole paying special attention to make sure wire and connector was on the backside of the insulation. Assembled the two screws and tightened.

1. tripped circuit breaker for stovetop
2. pulled the stove top out of its cabinet.
3. turned in over carefully due to the glass cooking surface.
4. used 1/4 inch nutdriver on cordless drill to remove all the screws holding the lower cover in place. lifted cover off without removing completely as power wires still attached.
5. did continuity test on burner and found it open circuit while all the other 3 burners had continuity.
6. removed defective burner by removing two more screws and saw element was fried on the cooking side.
7. wrote down all part numbers and put it all back together.
8. changed the burner out when new one arrived by repeating steps 1 thru 6. Pay attention to the correct wiring setup. Do one wire at a time to make sure you don't mess up. MAKE SURE THE CIRCUIT BREAKER IS TRIPPED BEFORE YOU KILL YOUR SELF.

Have a tall one to celebrate the savings of two repair man call out fee's of minimum $60 each time and paying list price for the element. You probably just saved yourself $150.
Tom in Steinhatchee

Removed 2 screws holding element to stove then gently pulled element forward to exposed lead connections and disconnected leads to element then reconnected leads to new element and gently pushed element ends back into the openings in the back of the stove and replaced screws to hold element to stove

Turned off the power . Removed two screws in front, lifted top, used a piece of wood to hold up,took off wires to bad element removed old element, replaced with the new one, put wires back on ,closed top,screws to front,on with power and cooked dinner!

First, thanks to PartsSelect for getting the part to me so quickly. I went to the "Instant Repairman" , checked all that applied to my problem. The answer was the sensor, 99% of the time.I used a coat hanger to pull the latch back and open the door. I watched the video and followed the instructions to remove the old sensor. The wires were melted but the plug was still good. I used one of the adapters to install the new sensor, then replaced the two screws inside the oven. I pulled the stove out because I had read in the reviews that you needed to get the plug behind the insulation away from the oven wall. I was lucky ,there was a small hole in the back ,right behind the sensor.I gently pulled the wire and plug to the back ,well away from the oven wall. Put the stove back in place ,threw the breaker and was back cooking again!! My stove has a downdraft vent, took me longer to hook the vent back up than to install the sensor..Oh yes, did I say,I am a75 year old female and I did it all myself..

Checked online to see what F3 readout on stove meant. It meant replace sensor. Ordered part on a Sunday and part delivered Tuesday, Monday being MLK day. Detached bad sensor(2 screws inside oven)had to pull new sensor connector through hole from behind as insulation was too heavy (only removed 4 screws on right rear panel.Clipped wires together and reattached sensor inside oven. A cakewalk.

I ordered the part one afternoon. It arrived before noon the next day. Then I simply removed the old seal (with about 2 dozen spring clips). Inserted the new part by carefully inserting the new seal into its corresponding hole at each end and then worked my way around the seal while inserting each attached spring clip into its corresponding hole.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires to remove the old sensor. Went on line to find out where to order it from. Ordered it, It was on back order but was only about 1 week to receive. Reversed the procedure. WA LA. It works great.

Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working correctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

Turn off breaker.
Remove knob, pulls off. Pulled stove away from wall.
Removed front panel with switches attached.
There are screws in front and back.
Removed screws that hold switch in place.
Transferred wires one at at time to get proper location.
Reverse process for reassembly
Gary in Ohio

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.