GFG464LVS2 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- karen from Thornton, CO
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken drawer glide
Used a phillips head screwdriver to remove the single screw holding the part in place and put the new one on. Finding the part on this site was a breeze and it arrived quickly. A first rate experience all around.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Mauldin, SC
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rear drawer slide was broken.
Undid one screw. Removed the broken slide. Replaced with new slide an fastened with the existing screw. Problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Woodbridge, VA
- Parts Used:
- WP9758079
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Ignater would ignate the first time, but then after the oven went off the ignater would not re-ignate and the ove would rmain off
The first thing you need to do is remove the racks from your oven.
Then look around at the back of your oven for the screws that hold the bottom pan down.
Remove those screws and remove the pan. Some need to slide back and then come up others will just pull up.
Remove the heat shield that is over the burner.
Remove the bottom drawer of your oven.
Now you should be able to see the igniter that sits on an angle by the burner tubes with a couple of wires coming out of it.
Removing the screws that hold the igniter is probably the most difficult part with some ovens. Sometimes it is easier to remove the whole bracket that holds the igniter and then remove and replace the igniter out of the oven.
The wires for the igniter will go to a Molex plug. Follow the wires and undo the plug. On many units it will be below the oven in the drawer opening at the top back. You will need to lay flat on the floor and reach back in to do this.
Once you have the old igniter out then you can carefully install the new one.
Check to make sure that you can feed the Molex plug and wires down through to the bottom before fastening the igniter.
Once the igniter is secured and the plug is connected, you can then replace the other parts in the reverse order that they came out.
Then look around at the back of your oven for the screws that hold the bottom pan down.
Remove those screws and remove the pan. Some need to slide back and then come up others will just pull up.
Remove the heat shield that is over the burner.
Remove the bottom drawer of your oven.
Now you should be able to see the igniter that sits on an angle by the burner tubes with a couple of wires coming out of it.
Removing the screws that hold the igniter is probably the most difficult part with some ovens. Sometimes it is easier to remove the whole bracket that holds the igniter and then remove and replace the igniter out of the oven.
The wires for the igniter will go to a Molex plug. Follow the wires and undo the plug. On many units it will be below the oven in the drawer opening at the top back. You will need to lay flat on the floor and reach back in to do this.
Once you have the old igniter out then you can carefully install the new one.
Check to make sure that you can feed the Molex plug and wires down through to the bottom before fastening the igniter.
Once the igniter is secured and the plug is connected, you can then replace the other parts in the reverse order that they came out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Michigan City, IN
- Parts Used:
- WP9758079
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Often would not heat. Burners on syove were O.K.
Removed door per instructions in manual. Removed racks and storage drawer per manual. Removed two phillips head screws holding bottom pan and removed pan. Removed two phillips head screws holding igniter tube (#12) and withdrew tube from the cavity. Removed two phillips head screws holding igniter and bracket to the tube. Unplugged elcetrical connection to igniter and installed new igniter in reverse order. Too bad the igniter wasn't the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Oceanside, CA
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Damaged Socket When Removing Bulb Base
This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernice from Phoenix, AZ
- Parts Used:
- WPW10118455
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
I broke the glass by hitting it with the edge of a broom
Clean off all broken glass and wipe down the debree,figure what side the glass goes then unscewed the base then the sides then add gorrilla glue on the edges to help set the glass in place had some hold it the screw th center bottom in first then got the sides in place with the bottom rack then screw it all back in to place making sure the side and top were in place right that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from East Elmhurst, NY
- Parts Used:
- WP9758079
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
oven not maintaining temperature
Replaced bake igniter only as recommended by others, no need to buy the whole unit. The bottom screw is difficult to access, use a 1/4 inch socket set with 8 mm socket. Advice to remove bottom storage drawer to make sure wire is connected to the igniter. So far it works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jasper from pekin, IL
- Parts Used:
- WP9758079
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven wouldnt stay lit
all I did was replace the igniter and that fixed my problem simple to do.
Was this instruction helpful to you?
Thank you for voting!