GGE350LWS00 Whirlpool Range - Instructions

My daughter repaired it without any problems.

Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Philips head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.

once i got down and in the oven ( Im 74) that was the hard part all the rest was 10minutes and very easy ....... turnoff the breaker or unplug the unit

First I disconnected the power! unscrewed the two screws holding element in place disconnected the wire clips from ends of element (be sure to hold them so they don't "retract" into the body of the oven) Connect the wire clips onto the new element and replace into original location and replace the screws. Turn power back on and start cooking again!

I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted

FOLLOWED INSTRUCTIONS AND READ THE HINTS FROM OTHER CONSUMERS. IT WAS VERY EASY.

Took the element out & cleaned the oven & put the new element in. Easy as pie.

removed 4 screws lifted off the face with switches replaced the bad switch and put the face plate back on. if you have any concerns just watch the video , part select has posted its great

only 2 screws held the element in place pulled the wires and replaced with the identical part very easy to do and thanks for having the part available

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.

Removed door, dissasembled door cleaned all broken glass, installed new glass, re-assembled door and put door back on oven.

Very simple project.

replacing this was very easy and simple. I removed the 2 screws holding the support bracket then the 2 screws in back of the elemant ,pull clips off the element then installed it back like it was .....very simple...

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

First I unplugged the range from the wall outlet power source...VERY IMPORTANT!!! Then I unscrewed the 2 mounts in the back of the range that hold the heating element in place. I removed the old and installed the new one and reattached the 2 new mounts with the original screws and plugged the range back into the wall outlet. Other than the small and dark work space inside the small oven, it was super easy to do and probably saved us $175!

Watched a utube video on replacing element on my model range. Found my Phillips screwdriver. An electric drill would have been a bonus but not necessary. Pulled out range, pulled out plug, removed 1 screw from the lower back cover, disconnected the 2 wires, went to the front and removed oven door and racks, unscrewed 2 screws holding the element. Put new element in and reverse dprocess. Test oven. It worked!!