RE963PXPT0 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Johnson from Norwood, CO
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element Failed
I had previously partially removed the element and tested with multi-meter to determine that it was not working (open circuit). Repair procedure follows:
Turned off Power
Removed 2 retaining screws
Pulled element out part way
Removed 2 spade connectors supplying power
Replaced element w/new element
Reversed procedure
Tested Oven; worked fine.
Turned off Power
Removed 2 retaining screws
Pulled element out part way
Removed 2 spade connectors supplying power
Replaced element w/new element
Reversed procedure
Tested Oven; worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from Spooner, WI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element went bad, will not work.
As soon the Bake Element has arive, I install it no more than 5 min... All I nedd was a Screw driver. It was so easy, Thank You PartSelet!
Was this instruction helpful to you?
Thank you for voting!
Heat in elements was inconsistent
Removed block (1 screw) Cut 2 connecting wires. Strip insulation. Attach new block with wire nut(per enclosed instructions) Heat shrink wrap with Lighter. attach block. 10 minutes: problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carolyn from ROGERSVILLE, TN
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element was broken
was very easy to install I only needed a phillips screwdriver to remove old part and install new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Fort Collins, CO
- Parts Used:
- WP8189867
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
light wont come on
Well, when you put the back cover on and screw it down make sure you have nothing touching the white wire leading to the oven light. I did and it blew the push switch when I threw the 220 breaker. Actually, the light was on when I came in the room, but when I pushed the switch on the front panel it sparked in the rear and popped the breaker. Then I saw the short and when I tested the switch it would not click. The install was fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from SEBASTIAN, FL
- Parts Used:
- WP688805
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The dryer nob wasn't working the dryer knob broke off inside the unit
It was very easy to install the new parts successfully thanku parts select I will always keep using your business the representative was so helpful and understanding my problem I wish I could remember his name he was outstanding and a 100 thumbs up to him
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marie from WATERBURY, CT
- Parts Used:
- W10291024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
my first order a small drip bowl
came only I had to order the set again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from YONCALLA, OR
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Heating element had a melt down and small explosion
Remove racks, extract two phillips head screws, pull out element, unattached wires, install new element, reverse procedure to complete installation. (Note: With the racks and element out, great time to clean oven.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from CHARLESTOWN, IN
- Parts Used:
- WP660533
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Element did not heat
Pulled out element, plugged in new element. About 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from MIDDLE RIVER, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element burned out
Turn off the oven circuit breaker. Remove 2 screws that hold the element in place. Carefully pull element out, about 3 inches and remove 2 attached wires by holding the element and pulling the wire clips off of the old element. Slide wire clips onto the new element and put the screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonda from PADUCAH, KY
- Parts Used:
- WP313307
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken burner control knob
Opened package and stuck it on. Easy - Peasy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Redding, CA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven element caught on fire!!
My husband is an over-the-road driver, so I have to do all of the repairs myself. I went to the breaker box and turned off the power to the range. Then I removed 2 screws, pulled the element out about 3", and disconnected the wires. I then connected the wires to the new element, pushed it back in place, and replaced the screws. We had Parmesan Chicken for dinner and my children were thrilled!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Veronica from Brunswick, GA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom element was burned out
I removed two screws, pulled it out a few inched and unpluged two wires. I then plugged the two wires into the new element slowly slid the wires and element back into place and put the two screws back in... and it worked perfectly. I did it all in less than five mins. And I am a 53 year old woman.No man was required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Arlington, NE
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
When the oven was on we noticed the bake element had a 1 inch section that was bright red. Upon closer inspection, after the oven was off and the element cool, corrosion like damage was apparent where the element had been bright red.
Naturally the oven turned was off but for added safety I also set the breaker protecting the oven to the off position. Where the element attaches to the oven there is a small plate with two screws holding the element in position. Remove these two screws and then gently pull the element out 2-3 inches, which will expose the electrical connection. Using needle nose pliers gently pull on one of the wires to remove it from the element. Now remove the other and discard the old element. Simply plug the new element into those wires and screw the plate back into the oven. Now turn the breaker back on and you're done. Super easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Raymond, NH
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
items in the oven were not baking properly. We discovered the bake elemnent wasn't working and looked defective in one part.
I removed the back panel, unplugged the wires, removed the 2 screws, replaced the element, plugged the wires back in and put the back panel back on. Now that I'm thinking about it, I guess I didn't even need to remove the back panel to replace the element.
Was this instruction helpful to you?
Thank you for voting!