RF386PXGT4 Whirlpool Range - Instructions

The repair was easy. I unplugged the stove, removed back panel, pulled knob and removed 2 screws to remove switch. Unplugged old switch, plugged in new one and installed the 2 screws for switch. Had to snap off stem for new switch to fit knob (easily done with pliers with provided notch). Put knob and back panel back on. Total time, maybe 20 minutes.

Unplug stove. Remove the two screws attaching the element to the rear of the oven. Carefully pull out. Disconnect wires. Reconnect wires. Screw back in. Done. The hardest part was moving the stove away from the wall.

Pulled range out from wall, unplugged AC, unplugged infinite switch, plugged in new switch, broke off end of stem, plugged AC in put range back and tested.

First Things first, unplug unit, remove rear cover with Phillips head screwdriver, disconnect, wires from broiler element which is the top, one, open oven, unscrew top screws first, then two at the back, wiggle out element, then reverse Steps , test repair before putting cover back on. Then ta-da, you saved yourself a $300. Service call to the appliance repair guy.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I disconnected power cord from house current. Removed back panels (2). I then removed round knob on front of range. I then removed the 2 screws holding the switch in place. After doing that, I gently removed the actual switch itself from back of face panel. I then separated the 2 elements of the switch.

I took new replacement switch and reinstalled the 2 parts of switch and placed back into hole in face panel. I reinserted the 2 front screws that holds the switch in place. I put the selection knob back on. However, the knob does not fit tightly. The shaft on the switch itself is to long, but the switch works fine. You do not even know that knob sticks out further than before. I plugged unit back into house current and tested range element to see if it works. It did so with no problem. I then replaced rear panels and secured all screws back to their original location and that was all there was to it.

No problem. Was a fast and effective installation.

Unplug and pull out range.
Unscrew the back of the range with Phillips #2.
Unplug wiring harness from switch.
Unscrew the switch from the front of the range with P2 driver.
Install and plug in new switch.
Remove the spring steel knob retainer from shaft.
Cut off extra knob shaft with dremel to match others (there is a narrow segment at the proper length).
Reinstall knob retainer, knob, and range panels.

Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place

I still don't have it back together! The first time we ordered the part the gentleman sent me the trim for the left side which seemed to be fine but while replacing it the old part (right side) broke. Ok. so I called to order same part but for the right side. Well, the lady told me I could only order the oven door trim kit, which seems to be too large. I don't think she understood me. Why the 1st time ordering I could get the left side only now when ordering the right side she says we don't sell it that way. Very confused and still can't use my oven since Dec,19th!!

The brief comments on how to with the order was most helpful, no problems replacing frame. Quality is good I thought the price was very high for the parts, considering plastic and metal pieces, but then again compared to new stove reasonable. Remove pieces replace back in order removed.

Element was sent by buyer, As they recommended, when model of stove given to them. It was upper right rear. When element came. First took off old element. ...Match both element , new element did not look exactly the same, small variation. It did not come on.. I moved old element from left side to right side . Old element worked on both side .. tried new element on left side also.. still didn't work.. so I called right away and explained.. new element did not work.. not defective, but, just wasn't the right one.. I had a specialist came and check it out also. I was told wrong element.

Unplugged appliance, removed the 2 screws that mount element. Unhooked the electric wires,with pliers.
Connected, the wires to new element replaced the 2 screws. And was done in about 9 minutes.

This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021.
George Clark

take off back panel, simply unplug the old switch and plug in the new one. Simple

took out the drawer by removing two fillips head screws, four more screws removed the drawer front. Two plastic push pins and the front panel was off. Put the new panel on secured it with the pins, attached it back on the drawer front, put in the screws and slid the drawer back in the stove, put the two screws back in, done deal!