GS395LEGQ0 Whirlpool Range - Instructions

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

I placed the new glass in place, and replaced the screws. What I really want to tell abut is how QUICKLY my replacement part came from your company. I was so upset when I broke the original glass, but the replacement glass arrived within 24 hours! It was wonderful! Thank you!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Ordered the replacement part., removed the old trim from the door and reinstalled the new trim. On the drawer glide, I simply reattached a new one to replace the one missing.

Remove the bottom drawer. Remove the two Phillips head screws on the top inside of the door. Pull up on the handle (CAUTION: Be sure to hold the glass front against the door while doing this or the glass front can fall, possibly damaging it. Remove the glass front by lifting it towards the top of the door. Remove the two side pieces and the bottom trim piece by unscrewing the Phillips head screws located on the underside of the bottom trim piece. Discard the old trim pieces. Attach the new metal bottom trim piece using three of the previously removed screws. Do not tighten the screws at this time. Each plastic side piece has a nipple at the bottom. Insert this nipple into the outermost hole at each end of the bottom trim piece. The edge of the flange on each side piece should face inward. Have an assistant hold the two side pieces against the door frame while you slide the glass back in. The inward facing flanges go UNDER the glass. Reinstall the top piece making sure the indentations at the top of the side pieces are under the top piece. Install and tighten the two screws that hold the top piece on. Tighten the three screws holding the bottom trim piece.

I used a screwdriver to take two screws out and then pulled up on the burner head. I then installed the new part. It works great.

To begin with,the symptoms were strange.....the burner would not ignite even though the igniter was glowing....but if you bumped anything in the broiler or pulled the drawer out and closed it abruptly,it would lite. This went on for a few weeks , until slamming and banging worked no more.(that was getting old anyway)I went ahead and ordered the igniter.It came fast and was very easy to replace.I went in from the oven,took out the racks and the bottom plate(2 screws), exposing the flame diverter that is just above the burner.(2 screws)You can access the igniter now ,and remove it.(2 screws),and unplug it.Reverse order to install the new one.I didnt unplug the range or turn off the power,because I screwed the igniter on first and then it was a matter of just plugging it in. Everything went back together and turned on the oven. Worked fine. Very easy to do,and no more banging around the broiler.Should have done it sooner.

I shut off the gas and removed the back plate and disconnected the wires. Then I unscrewed two screws from the igniter and replaced the old with the new. Then I snapped the wires together and put the back plate back on. The oven works great!

The kit was not supposed to fit my particular model but I felt the picture was exact and took a chance and had it sent. It was a perfect fit and was easy to assemble and looks like a new stove. I paid one third of the cost estimates that I got from local appliance centers and even other on line sites. I'm very please with the product and the delivery was more than prompt!! I couldn't believe the service!!! Thanks!!

most difficult part was having to pull the stove out to access the Igniter wire connector. unplugged connector, removed 2 Igniter mounting screws, installed new Igniter and connected plug. very easy project. less than 30 minutes total thanks to website for perfect diagnosis of problem

Opened lower door of stove located ignitor removed 2 small screws that secure part, took guard off back of stove unplugged wire connector removed part plugged new ignitor in re-installed guard, re-installed 2 screws that secure ignitor. Turned stove on oven lit problem solved. This is the 3rd time i have used instant repairman on parts select to fix 3 different applicances and have saved hundreds of dollars fixing it myself with the help of parts select.

Really quite simple. Remove the racks - remove the two screws in the back of the bottom plate - slide out. remove the bottom drawer. remove the two screws holding the igniter - unplug the old igniter and remove. screw in new igniter, plug up new igniter, replace bottom drawer, replace bottom pate, replace racks. I did turn off the gas and electricity to the unit before repairing - and it was easier for me to get behind the unit to unplug/plug the igniter. works great! thanks!

I pulled the stove out from the wall & took the back lower right cover off. Unplugged the power cord & disconnected the igniter from the power. Took shelves & bottom cover (took two screws out)from oven. Used nutdriver to remove old igniter, then pulled the connector through into the oven, discard. Put new igniter in place with nutdriver.Push connecting cord through to back of stove.Replace bottom cover & shelves. Plug cords together & plug cord back in to outlet.Turn stove on & igniter works!!! Push stove back into place & bake a cake! :)

I removed the oven racks, removed the oven floor and the oven burner cover, pulled the range out and removed the small panel on the back which covers the igniter connector. I disconnected the old igniter, removed the two screws holding the igniter in place and removed the old igniter from the oven. Then screwed on the new igniter, fed the wire through to the back and connected the new igniter. Turned on the oven and voila' we have ingnition! The oven is working again but I'm getting the "F2" routine sometimes. It doesn't do it every time but when it does I unplug and replug and then it works. I'm a 67 year old female and I considered it very easy so pretty much anyone should be able to do this repair.

The first challenge is always how to get the appliance apart; in this case how to open the top of the stove. There are two clips one on each side towards the front that you need to push in to release the top. However before you do this you need to unscrew and remove each of the burners from the top of the stove. After that, push the clips in with a flat blade screwdriver from each side to lift up the top. You will need to remove completely the top back plate on the rear of the appliance to get to the igniter module where you plug in the wires from the individual igniters. Then you also need to remove the top four screws from the lower rear plate to allow it to be pulled open enough to help thread the wire from the new igniter through. After that you simply figure out which wire (they are individually colored based on their position on the burner) and disconnect from the igniter module. Carefully pull it out watching where it came from so you can rout the new wire in a similar manner. Then remove it completely pulling it through the top of the stove and replace with the new igniter. Reverse the steps to put everything back together and you should be good to go. Be prepared to take a little extra time to clean the cook top as once you remove the burner you will see everything that has over the years accumulated between the burner and the stove top. All together it took me about a 1/2 hour (including the cleaning).