RS696PXEQ2 Whirlpool Range - Instructions

1) Removed the trim pieces (2 screws). 2) removed the 2 screws holding the oven in the wall. 3) Slid the oven out of the wall cabinet 4) removed the back panel of the oven ( 10 screws. 5.) removed the old thermostat (2 nuts) 6.). Installed the new thermostat and reversed steps 4-1

Small, older female with limited hand strength here. Turned off the power to the stove. Removed the baking element from the oven wall with a screwdriver, snapped out the old one and snapped in the new one. 5 min tops. The broiler was a bit more labor intensive as the rusted and/or stripped screws did not want to come out. Used some liquid wrench, gripping grit, and a power drill to remove, but once the screws were out, it was another easy snap off/snap back in process. Had some screws on hand to replace the stripped ones. Broiled a steak that night with the new red hot broiler. So happy. This repair just saved me approximately $1800 to replace a 28 yr old drop-range. Very happy with this purchase.

Opened overn door and inserted allen wrenchs through the holes in the door hinges. Close the door until it makes contact with the allen wrenchs, then grasp the oven door handle and the bottom of the oven door and lift up to remove the door. Place the door on a flat surface,(I used a bed) and remove the screws to gain access to the glass. Upon re-assesbly, leave door flat line up and re-install all screws before putting the front pannel back on. Insert door back into the oven and open, remove the allen wrenches and close the door. The process is easy and will take 30 minutes to an hour and save you a $100.00 service call!

Since there is multiple glass panels with several brackets, screws and insulation within the oven door I strongly suggest to take photos at each step using your smart phone. Do not attempt to remove all the components at once. Bracket positions, screw locations and glass orientation is necessary. This is the best advice I have to make this a quick and very easy job.

Easily, Removed the oven with help of my grandson, this model is quite heavy. Open the back cover panel, removed the old blower. replaced with the new blower, covered with the back protective panel. About one hour because some screws much harder to reach.

I turn off the power in the breaker box and then unscrew the part and replace it with the new one

After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.

unscrewed the oven door, took off the entire door, pulled apart the glass pieces and replaced

ordered new broiler pan

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Read the instructions in installation manual to remove door. Kept removing screws. Was surprised to find two panes of glass between the inner glass and the outer glass. Cleaned all the glass (4) and the inside of the door. Looks brand new. Be careful with the insulation; be sure it is pushed back or it will show from the outside.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

I removed the Oven door, unscrew 10 screws, open up the dor case, clean all glass levels, replace inner glass, reassembled the door, reinstalled the door to the appliance.

removed door from oven, took all screws off door to remove glass, put new glass in place, put oven door back together, put oven door back onto the oven

It went fine once you imbeciles sent the right part, thank you for miss labeling it on the website and costing me time, a week without an oven, and extra expenses. The inner GLASS is the inner GLASS, not the middle glass of a layered three glass door!