RF391PXWW1 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- brenda from las vegas, NV
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom element burnt out
removed 2 screws . pulled out the 2 wires and disconect them. took out the element. Put the new element in and hooked the wires up. placed the metal bracket to the back and put in the 2 screw and turned it on and it worked like new.
Brenda
Brenda
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from South Burlington, VT
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not heat up
Just like you said,remove two screws,pull out element,disconnect wires,install new part. It was easier to pull out stove and hook up wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Redding, CA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven element caught on fire!!
My husband is an over-the-road driver, so I have to do all of the repairs myself. I went to the breaker box and turned off the power to the range. Then I removed 2 screws, pulled the element out about 3", and disconnected the wires. I then connected the wires to the new element, pushed it back in place, and replaced the screws. We had Parmesan Chicken for dinner and my children were thrilled!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Veronica from Brunswick, GA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom element was burned out
I removed two screws, pulled it out a few inched and unpluged two wires. I then plugged the two wires into the new element slowly slid the wires and element back into place and put the two screws back in... and it worked perfectly. I did it all in less than five mins. And I am a 53 year old woman.No man was required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from MIDDLE RIVER, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element burned out
Turn off the oven circuit breaker. Remove 2 screws that hold the element in place. Carefully pull element out, about 3 inches and remove 2 attached wires by holding the element and pulling the wire clips off of the old element. Slide wire clips onto the new element and put the screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from PUTNAM VALLEY, NY
- Parts Used:
- WP8053344
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven was overheating and locking the door. Codes indicated the temperature sensor could be the issue.
Only one screwdriver needed for this simple repair. Unfortunately for me it did not repair my oven and a new code on the oven indicated a bigger problem with computer board.
Part Select was great to work with and accepted a return and promptly refunded me for the part.
Thank you!
Part Select was great to work with and accepted a return and promptly refunded me for the part.
Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from CHARLESTOWN, IN
- Parts Used:
- WP660533
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Element did not heat
Pulled out element, plugged in new element. About 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from PETALUMA, CA
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Wouldn't Heat
Of course, power off first, then I removed the old one and inserted the new one, make sure everything in right place, then turn on power, simple as 1-2-3.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- denise from swartz creek, MI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element quit working
Removed the 2 screws that hold the element in place. Pulled the element forward about 3 inches and disconnected the two wires. Plugged the wire clips onto the new element and pushed the element back into place. Put the 2 screws back into place. This was a very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lowell from Aberdeen, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turn on the oven to heat up for cooking, Heard a ark sound, open the oven door and there was a fire on the element. Turn off the oven.
I had to pull the stove out from the wall and discounted the power source from the wall. Than I used the a phillips screwdriver take out the heat element. There was now problem fixing the stove. Lowell Moxley
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from burnthills, NY
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out bake element
unscrewed two screws put in new element replaced two screws done, recieved the element within days of order,it was the right part,couldn't have been happier with the service from parts select thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from COVINGTON, GA
- Parts Used:
- WP8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stove got way too hot
Took the back off the stove, removed 2 screws, unclipped the bad sensor, clipped the new one on, put the screws back in and the back of the stove back on and that was it - 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heriberto from AUSTIN, TX
- Parts Used:
- WP8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
THE OVEN WAS NOT HEATING TO DESIRED TEMPERATURE
DISCONNECTED POWER AND GAS TO THE RANGE. REMOVED 6 SCREWS FROM REAR OF THE RANGE. REMOVED THE 2 SCREWS HOLDING THE TEMPERATURE SENSOR IN PLACE. DISCONNECTED THE LEAD FOR THE SENSOR. INSTALLED NEW SENSOR IN REVERSE ORDER. OVEN WORKING PROPERLY NOW.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from COON RAPIDS, MN
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Worn/Bulb Socket
It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from Chesterfield, MO
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
old heating element "popped"
Ordered the part Friday afternoon. It was delivered early on Saturday afternoon. Very impressed with the speed of the delivery! Power off, unscrew the old part, replace, screw the plate back on. Easy!
Was this instruction helpful to you?
Thank you for voting!