RF314PXYN2 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson A from Feeding Hills, MA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven Bake Heating Element burned out.
First I removed the two screwes that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires from the old element, then I connected the two wires to the new oven heating element. Pushed the unit back in place and reinstalled the two screws that hold it in place.( ALL Done)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from UPPER MARLBORO, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The old bake element had burned out
It was so easy. I removed the baking racks. Then I unscrewed two Philips head screws that held the rack in place. Then I pulled the two connections apart from the wiring. Plugged the new element into the wiring. It was as simple as sliding it in and out, replaced the screws, and within minutes I was back to baking again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Caddo Mills, TX
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Inside Light would not work
Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Ticonderoga, NY
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Baking element burned out
I removed the screws that hold the element in place .
Pulled the element out enough to disconnect the two wires . I then connected the new wires and pushed in the element . I finished off by screwing the bolts back in place.. Voila!!!!!!! I was in business once more!
The part arrived within 48 hours and was very reasonably priced
Pulled the element out enough to disconnect the two wires . I then connected the new wires and pushed in the element . I finished off by screwing the bolts back in place.. Voila!!!!!!! I was in business once more!
The part arrived within 48 hours and was very reasonably priced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Latrecia from Antioch, TN
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake element caught on fire & broke into 2 pieces.
Shut power off to stove, by turning off breaker. Using a screw driver, removed the 2 screws securing broken bake element to back of oven wall. Grasp the 2 wires holding the prones & gentley removed broken element. Attached new bake element to wires, put screws back in & secured to oven wall, turned breaker to stove back on. Oven works great, had pizza for dinner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Birmingham, AL
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
broken bake element
Fairly easy to do. Part arrived very quickly. Appreciate
associate's help in making sure part was right.
associate's help in making sure part was right.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- judy from spring hill, FL
- Parts Used:
- WP308180
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
My husband, not a Mr. Fix It. And I would have done it myself but I had hurt my back and could not get down to do it.
Don't know, left the room.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from Valley, AL
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven bake unit burned out several years ago
Replaced for a friend who was financially unable to purchase the unit. Turned off power to stove. Removed two screws. Inserted the unit and replaced the two screws. All fixed in about 15 min. Now she can enjoy baking again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Spencer, MA
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
3 inch segment of element separated from the whole element
Shut off circuit breaker to stove. Removed oven racks from oven. Removed two phillips head screws located at the base of the bake element at the back of the oven. Gently pull the element toward the front of the oven until the wiring connected to the element by spade connections can be reached. I used a pair of pliers to help separate the element from the wiring. Removed disfunctional element from oven. Sweep out the bottom of the stove with a dustpan & brush. Lay the new replacement element on the bottom of the oven. Connect element to wiring via spade connectors. Gently feed the wires back thru the holes until the the tips of the element follow thru the wire holes until the base of the element is flat against the back of the oven. Screw in screws thru the base to the back of oven - tighten tight. Reset cir brkr. Test oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from Villa Grove, IL
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven heating element needed to be replaced after failure
I had previously removed the element so I began by installing the new element. The wire connectors, did not fit as tightly as they did on the old element due to a slightly different shape on the element. Therefore, I had to take some needle-nosed pliers in order to bend the oven's wire connectors and make them fit tighter. Once that was done I struggled a bit to slip the connectors onto the new element but finally got them on.
There is also a 208V element available for this oven but after calling the web site's phone number was advised that the 208v is for an apartment-type oven and that the 240V is appropriate.
Everything works well!
There is also a 208V element available for this oven but after calling the web site's phone number was advised that the 208v is for an apartment-type oven and that the 240V is appropriate.
Everything works well!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- G Weir from Ocoee, FL
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace bake element in 20 yr. old wall oven
followed the instructions. removed the old element and installed new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn R. from Cambridge, ME
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The oven heating element had a bright spot in it and I was afraid it would blow while I was cooking.
My husband said HE JUST TOOK OUT A COUPLE OF SCREWS ,TOOK THE OLD ONE OUT AND PUT THE NEW ONE IN .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Crimora, VA
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Block broke
Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Las Vegas, NV
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light burned out in upper oven
Screwed in light bulb and glass protector
Was this instruction helpful to you?
Thank you for voting!