SF375PEWW3 Whirlpool Range - Instructions

First I turned off the gas supply to the oven and disconnected it. I then pull the oven out away from the wall. I then unplugged the power cord. I removed the oven door by lifting it off of it spring hinges. I then removed a lower plate that covers the burner element by pressing in a manner that it popped off. I then located the ignitor and removed 3 screws. All were easily removed. Carefully, I pulled the igniter out and removed the wires from the wires that supplied the current to the ignitor. Installation followed by working the steps above in reverse order.

Al lI had to do remove the oh swith & attach th e new on & push in place
It took about 5 min. to turn off the electric & to turn it back on.
Glen V

unscrewed the bracket holding the igniter in place then we pulled the drawer on the bottom out and disconnected the Igniter - then we took the unit out of the bracket replaced it and then put the bracket back into place screwed it in and reconnected the igniter and now it burns hotter then it has since we moved into the house two years ago.
I was worried that it would be a hard long job but was pleasantly surprised when it only took a few minutes.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

We unplugged the stove and turned off the gas. We slid the oven door off just to make it easier. Unscrewed 3 screws holding the igniter in place. Pulled the igniter out from the back of the stove. Disconnected the two wires. Slid the new igniter in the holder. Rewired it and slid it back into place. Put the screws back in and it was done. Plugged it back in, turned the gas on, tried it out and presto! It was perfect! Lit immediately and strong and now i have a brand new 20 year old stove. lol Happy girl! And this was done by 2 50 year old women!

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

The first igniter was received broken. A replacement was received within 5 days. It was very easy to install once the protective cover was placed over the igniter end. In my opinion, this part should be sold with the protective cover already in place.

Removed old igniter and replaced with new one.Tested oven and it went on. You need a phillips screwdriver to remove two screws and a small socket for the third screw to remove the igniter cage. Then pull out the wires from under the oven and disconnect. Reverse procedure to install new igniter. Reuse original connectors. Be very careful with the igniter because the tip is very fragile and can break easily.

Followed instructions that came w/ NEW PART. Very straight forward.

After too many years of trying to make do with worn out burner bowls, I finally searched on line for Caloric replacement parts. My order arrived THE NEXT DAY(!!!)and make my old range look almost new! They are so shiny and clean, and fit perfectly. I am so pleased, and wish I had ordered from PartSelect years ago! Thank you for your speedy service!

Roommate did the repair..so I don't know. I did the research online, the igniter solved the problem. Saved us buying a new oven!

bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!

Replaced the igniter. Took out the 20 screws holding the bottom plate of the oven. Removed the igniter and gas tube mounting screws and bracket. Took off the wire nuts that attached igniter to stove wiring. Carefully installed new ignitor, using reverse of the steps above. Igniter tip is very fragile, so beware as you handle. All went very well, and oven now works like a charm

My 1st thought was that the valve was bad but after watching a whirlpool video on how to trouble shoot I put an amp probe on the wire to the igniter and discovered that the amp draw was not getting high enough to open the valve. The vale calls for 3 amps but the amps on the igniter only got up to 2.4 amps even though the igniter was glowing red hot. I ordered the new igniter from PartSelect and it was here in less then 2 days. It was a perfect fit and took about 30 mins. to install and it works perfectly. I also ordered a motor and a blower wheel for a Whirlpool Electric Dryer, Model #LEC8858EQO, and it arrived in less than a day and again both items were an exact fit and the dryer now works perfectly. Great service and fast response by PartSelect. I will defiantly use PartSelect again.

First, my wife and I pulled out the oven from wall to disconnect electric plug and, also with a wrench; I shut off the gas connection on the wall. I then removed front door of the oven by pulling up on door to have easy access to lower part of oven, and then removed pan to get to Igniter. Removed the three screws on cage that supported the Igniter and, I also had to remove several screws to the manifold and bottom pan that supports the manifold so that I could disconnect Igniter. I then was able to pull out old Igniter and, reconnect the new one. After that, I reinstalled everything in reverse. Before pushing oven back into wall; we made sure the new igniter worked. It worked just great. My wife and I were so happy and proud that we done it our self, and not have to call someone to do it for us. It took me and, my wife about an hour and a half to complete the job. I believe the reason it took us as long as it did was because we really didn't know what to expect. Now that we know; I am sure that we could do it again in 30 to 45 minutes. Dave & Marsha; 8/23/2013