RF316PXYW3 Whirlpool Range - Instructions

Funny, I suppose. We decided to buy a new stove given the old age of the old one. Problem is, on delivery day it wasn't delivered and we discovered that there wasn't even one in the warehouse. At that point we got ticked and decided to look into the problem. The website led us right to the problem. We ordered, the part arrived the next day and the replacement was simple. Just unscrew the holder inside the over, unplug the old element and plug in the new. I needed needle nose pliers because one of the wires slipped behind the insulation. We also bought a thermometer and found that the calabration was right on the money. Happy campers... we saved $400.

Found breaker box and shut off power to stove, Check to make sure you turned the right breaker off before you attempt to put you hands in it, also make sure all the switches on the stove are in the off position . Open Oven Door, I used a Phillip screw driver to remove the two screws holding the Bake element in place . pull out to reach wire connections and gently pull connectors from element. Remove the old Bake element and Install the New one,by reversing process in removing the old one. after you have it back in place turn breaker back on at breaker box turn oven control to Bake setting, turn Oven Temperature control to around 200 degrees and Element should began to glow bright orange, job complete, it's that easy!~

Turned off electric to oven by shutting circuit breaker.Opened oven door, took out baking racks,loosened bolts from rear of oven holding element and plate . Disengaged element with plate from wires at rear of oven. Attached new element to clips on wires, rescrewed element plate back to rear wall. replaced racks and turned on circuit breaker. DONE!
Thanks for the quick service ordered one day, next day delivery, never missed a meal or dessert.

Made sure that "Breaker" for oven is in the off positon.

Opened oven door to the first "stay open" position...lifted door straight up...and off of the hinges....which removes the door....and allows easier access to oven.

Removed oven racks

Removed two philips head

Pulled burned out element toward the front of the oven.....exposing the two connector wires.

Used pliers to pull wire connectors from burner element connectors.

Reversed the order of this process....to install new element.

un plugged oven from wall Unscrewed 2 screws pulled out old heating element and plugged in new heating element then plugged stove back in

1) Turn off the power at the circuit panel!
2) Remove 2 screws at the back of the bake element.
3) Gently pull the element out about 6 inches.
4) "Unplug" two wires from the back of the element.
5) Do the same in reverse to put the new element back in.
6) Turn the power back on.
7) Done!

Screwed in light bulb and glass protector

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

I unplugged the stove/oven then unscrewed the bottom element (two screws in the back). I pulled the two electrical clips off the old bake element then removed it. I pushed the electrical clips on the new back element then screwed it back in. After plugging the oven back in and turning it on the oven worked perfectly!

i removed the back cover unpluged 2 wires
inside the oven removed 2 screws from the element . reversed the process to re install the new part

Simply remove two phillips screws, unplug and replug. Thanks to the quality parts I bought here it saved me $65.00 on the part alone. Locally $85.00 plus shipping.
Thanks guys for your help.

Turn power off, then removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected new element, put screws back in and test.

removed the old one replaced the new one every thing works like new. THANKS

i received the part via fed-x i opened the box uninstalled the old part installed the new part turned it on the element got red hot and it works just fine.

I order the part on 7/29 and much to my surprise, it arrived the very next day. It took less than 15 minutes to remove the old element and installed the new one. It was a little difficult to unplug the old one and took quite a bit of pulling but it came out okay. Plugging in the new one and screwing on the cover plate was easy.