RS6100XKW1 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from CHARLESTOWN, IN
- Parts Used:
- WP660533
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Element did not heat
Pulled out element, plugged in new element. About 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from YONCALLA, OR
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Heating element had a melt down and small explosion
Remove racks, extract two phillips head screws, pull out element, unattached wires, install new element, reverse procedure to complete installation. (Note: With the racks and element out, great time to clean oven.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ramiro from AUSTIN, TX
- Parts Used:
- W10900107
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Surface Element switch faulty with no control on heat
Turned power completely off. Removed knob from front panel. Opened range top cover. Removed 3 screws from aluminum panel protector behind the element switch. Once panel is removed you can see the switch element. Remove 2 screws from the front panel that connects to the element switch. Remove the old element and replace with new element making sure that each of the 5 wires on the old element is transferred one by one to the new element. Reverse the process in putting it all together. Turn on the power and walla you've have a new stove. You just save $600 plus.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from Monroe, NC
- Parts Used:
- WP3150371
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replacing the cracked oven knob.
Was waiting on my friend's boyfriend who is a contractor to switch this knob out but figured it out myself. It just slides on and off with no tools. I am so proud of myself for completing the repair all by myself on my 37 year old oven. My other knob just cracked and I was afraid the inside of the knob was damaged but it is not. Working like a charm now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from ROBBINS, NC
- Parts Used:
- WP3150371
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The two oven control knobs were broken.
The new knobs slide on and fit perfectly. No tools or labor required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from MIDDLE RIVER, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element burned out
Turn off the oven circuit breaker. Remove 2 screws that hold the element in place. Carefully pull element out, about 3 inches and remove 2 attached wires by holding the element and pulling the wire clips off of the old element. Slide wire clips onto the new element and put the screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Redding, CA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven element caught on fire!!
My husband is an over-the-road driver, so I have to do all of the repairs myself. I went to the breaker box and turned off the power to the range. Then I removed 2 screws, pulled the element out about 3", and disconnected the wires. I then connected the wires to the new element, pushed it back in place, and replaced the screws. We had Parmesan Chicken for dinner and my children were thrilled!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Veronica from Brunswick, GA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom element was burned out
I removed two screws, pulled it out a few inched and unpluged two wires. I then plugged the two wires into the new element slowly slid the wires and element back into place and put the two screws back in... and it worked perfectly. I did it all in less than five mins. And I am a 53 year old woman.No man was required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brenda from las vegas, NV
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom element burnt out
removed 2 screws . pulled out the 2 wires and disconect them. took out the element. Put the new element in and hooked the wires up. placed the metal bracket to the back and put in the 2 screw and turned it on and it worked like new.
Brenda
Brenda
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Arlington, NE
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
When the oven was on we noticed the bake element had a 1 inch section that was bright red. Upon closer inspection, after the oven was off and the element cool, corrosion like damage was apparent where the element had been bright red.
Naturally the oven turned was off but for added safety I also set the breaker protecting the oven to the off position. Where the element attaches to the oven there is a small plate with two screws holding the element in position. Remove these two screws and then gently pull the element out 2-3 inches, which will expose the electrical connection. Using needle nose pliers gently pull on one of the wires to remove it from the element. Now remove the other and discard the old element. Simply plug the new element into those wires and screw the plate back into the oven. Now turn the breaker back on and you're done. Super easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from South Burlington, VT
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not heat up
Just like you said,remove two screws,pull out element,disconnect wires,install new part. It was easier to pull out stove and hook up wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lansing, MI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bad element in oven
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then reverse the process and bingo ...done
EXTREMELY fast shipping of product ...I have purchased other products and always satisfied .
Then reverse the process and bingo ...done
EXTREMELY fast shipping of product ...I have purchased other products and always satisfied .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Abingdon, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The baking element had burned out
First, turn the breaker off to the oven, you don't want to electrocute yourself. There are two screws that hold the element to the back wall of the oven, undo those and pull the element towards you. There are two terminals at each end of the element, take these off, then reattach to the new element and screw back in to the back wall of the oven. This process takes maybe all of five minutes
Was this instruction helpful to you?
Thank you for voting!
Bake element blew
remove all element that is held with two screws and install the new one. easy fix! and a lot cheaper than a new stove!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Olathe, KS
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element burned out - Easy repair
Took a phillips head screwdriver and took out the two screws. Lifted off small plate securing screws, pulled lightly and wiggled the element out and popped the new one in. Total time 7 minutes - yes we timed it!!! Fast delivery too!!!
Was this instruction helpful to you?
Thank you for voting!